塑料的进料点英语要怎么翻译

❶ 模具术语中进胶口（点胶口）英文怎么说

gate type: pin point gate.
通常译为浇口，而非“胶”内口。浇口类型通常分为侧浇口(side gate)，潜浇te(sub gate)，点浇口(pin point gate)，扇形浇容口(fan gate)等等。

❷ 英语翻译:塑料的

plastic

❸ 塑料英语谐音怎么说

你好!
塑料
plastic 英[ˈplæstɪk] 美[ˈplæstɪk]
n. 整形; 塑料制品; 〈口〉（使用）信用卡; 可塑体;
adj. 可塑的，塑性的，受回范的，柔软的; 造型答的，塑造的，给与形态的; 塑料[塑胶]的，塑料[塑胶]制的，合成树脂做的; 有形成力的，有创造力的;
[例句]A lot of the plastics that carmakers are using cannot be recycled.
汽车制造商使用的许多塑料制品是无法回收利用的。

❹ 有懂塑料专业术语的英语高手吗翻译

Drainage opening material（水口料）

你可以参考下：）~~
Drainage是排水设备的意思，也许与水口料有关吧：）~~希望能帮助你一点：）~

❺ 塑料制品的外贸翻译,在线等!

Tags drinks, candy bags, tea bags, cold bag, liquid bag, cooking bags, MSG BAG, medicine bags, paper plastic bag, easy to tear BAG, veterinary medicine bag, cynthiaMedicine bags, parts bags, chain bags, handbags, three-dimensional bags, all kinds of membranes, a single-storey volume sealing membrane, double, multi-layered composite membrane volume

❻ 关于塑料材料的商检英语

The cup is made up of plastics thus it need the inspection.Generally,the ration of inspection is 1-2 working days,and the quantity should be above 80% of the cargoes.It is necessary to proceed inspection if the carrier arrived to the mill tomorrow.Therefore,the time is insufficient,and we will commence the customs procere only after the completion of the inspection.As you known,may 1-3 is the vacation in China,the customs institution and shipping company is not working then,so we are worried that these two carriers will miss the vessel.

❼ 塑料的英语翻译 塑料用英语怎么说

塑料
[词典] plastic; plastics; plastic material; plastomer;
[例句]我在容器上盖了一片聚乙烯塑料薄膜，解决了版这个问题。权
I have overcome this problem by placing a sheet of polythene over the top of the container

❽ 进料的英语翻译 进料用英语怎么说

你好!
进料
feed 英[fi:d] 美[fid]
vt. 喂养; 满足（欲望等）; 向…提供; 供…作食物;
vi. 吃，以…为食; 流入，注入，进入（如油流入机器）; [电子学] 馈入;
n. 饲料（尤指粗饲料），施肥; 喂送; 草料; （尤指向地方性电视台） 馈送电视节目;
[例句]We brought along pieces of old bread and fed the birds
我们拿了几片陈面包来喂鸟。

❾ 塑料英语翻译

塑胶原料材料微丸/regrindoffgrades/慢/一流材料

❿ 关于塑料的英文翻译（需专业）

解答如下：GE Plastics
Generally refers to volume of proction, use wide, forming good, cheap plastic, such as polyethylene, polypropylene, phenolic, etc..
GE Plastics has five varieties, namely, polyethylene, polypropylene, PVC, polystyrene and ABS. They are thermoplastic.
Polyethylene (PE)
Polyethylene is a plastic instry in the most proctive varieties. Polyethylene is opaque or translucent, light crystalline plastics, with excellent low temperature performance (the lowest temperature can reach -70 ~ -100 ℃), electrical insulation, chemical stability, capability of most of the acid-base erosion, but not heat. Polyethylene suitable for use on injection molding, blow molding, extrusion methods such as machining. PE can be classified according to different densities: low density polyethylene LDPE; high density polyethylene HDPE; linear low density polyethylene LLDPE.
Polypropylene (PP)
Polypropylene is a thermoplastic derived from propylene polymerization, usually colorless, translucent solid, odorless non-toxic, a density of 0.90 ~ 0.919 grams / cm, is the lightest of GE Plastics, which highlight the advantages are in the water-resistant cooking characteristics, corrosion resistance, strength, rigidity and transparency better than polyethylene, drawback is poor low-temperature impact resistance, easy to aging, but can be respectively, through modification and adding additives to be improved. Polypropylene proction methods are slurry, Liquid Bulk and Gas Act 3.
Polyvinyl chloride (PVC)
PVC is a polymer derived from vinyl chloride plastics, by adding plasticizers, its hardness can be changed significantly. It is made of hard procts as well as soft procts have a wide range of uses. Methods of proction of PVC suspension polymerization, emulsion polymerization, and bulk polymerization, suspension polymerization in the main.
Polystyrene (PS)
Polystyrene is a versatile polymer of styrene, appearance and transparent, but the shortcomings of brittle hair, therefore, polybutadiene can be made by adding high impact polystyrene (HTPS). The main proction methods of polystyrene bulk polymerization, suspension polymerization and solution polymerization.
ABS
ABS resin is acrylonitrile - butadiene - styrene monomer co-polymerization of three kinds of procts, referred to as ABS terpolymers. The plastic because of its components A (acrylonitrile), B (butadiene) and S (styrene) in the proportion of different composition, as well as differences in manufacturing methods, the nature there are very different. ABS for injection molding and extrusion processing, so its use also mainly the proction of these two types of procts.