摩擦装置英语怎么说及英文翻译

㈠ 摩擦用英语怎么说

还有rub或者scrape！

㈡ 英语翻译

Since transmission input shaft and output shaft to the speed of their rotation, transform a stall when there is a "simultaneous". Two rotational speed is not the same gear forced meshing impact of the collision will occur, damaged gear. Therefore, the old transmission to shift the "two-off" approach, or file location in the free stay for a while, by stalls in the free position refueling door, in order to rece the speed differential gears. However, this operation is more complicated, difficult to grasp accurate. So designers created a "simultaneous", to be adopted simultaneously allows the meshing of gears to achieve the same speed and smooth meshing

Adjacent stall conversion, we should take different steps of the truth applies equally to the mobile gear shift, the question is the former joint engagement ring gear and sets the requirements of the same angular velocity rotation, and the latter the question of joint gears meshing point Line speed, but the analysis is based on the principle of speed is the same.

Transmission shift operations, especially from high-end of the shift to low-grade operation is more complicated, and it's easy to spend a tooth or the impact of bond between teeth. To streamline the operation and avoid impact between teeth can shift device set Synchronizer

After the synchronization with the research and development, now has a synchronizer-atmospheric, and inertial force of inertia by three. Although the pressure synchronized with simple structure, but there is no guarantee that in the teeth of a synchronous state (that is the same angular velocity) shift the shortcomings, now is not in use. Been widely used is customarily synchronizer.

Synchronization inertia, mainly from the joint units, composed of sync lock ring, which is characterized by relying on the role of friction synchronized.

Joint sets, to be simultaneously lock engagement ring and the ring gear on the gear are Chamfer (Lock Kok), lock ring simultaneously with the question of the cone gear engagement ring gear, cone contact with friction. Lock angle in the design and the cone has made the appropriate choice, cone friction that makes the engagement ring gear tooth sets and the rapid synchronization, and will proce a Lock role and to prevent the gear before engaging in sync.

When the lock ring simultaneously with the question cone gear engagement ring gear, cone after contact friction moment in the role of the rapid speed of gear to rece (or increase) to synchronize with the speed equivalent to lock ring, the two synchronous rotation, relative to gear Central lock synchronization speed is zero, thus inertia torque also disappeared, then in force under the impetus of engagement sets unhindered and synchronization lock Gear engagement ring, and further engagement with the question of gear engagement ring gear and completed Shift process

The topics mainly through the Pro / E (or UG) synchronization software for the car to three-dimensional modeling structural design, and through the parameters of the design process to achieve its structure, and on this basis, the use of ANSYS FEM software structure of the typical synchronization And a finite element analysis, through structural analysis of its structural design is reasonable to assess and make recommendations to improve the design

㈢ 英文翻译

3.23 LUBRICATION
3.23.1 Oil lubrication shall be provided for enclosed gear trains and speed recers in accordance with section3.14 .
3.23 润滑
3.23.1给闭合齿轮传动链和减速机做油润滑须依照3.14章节来进行。

3.23.2 Lubrication of other mechanical operating parts shall be means of a high pressure gun . Buttonhead type grease fittings made of brass , monel or stainless steel shall be used throughout . This requirement does not apply to bearings where overgreasing can damage the equipment , such as an electric motor . Special lubrication fittings shall be used in these case that can be accessed only by specially trained personnel with the proper lubrication equipment .
3.23.2 其他机械操作部件的润滑须使用高压油枪。应始终使用黄铜、锰合金或不锈钢制成的扁圆头类型的黄油嘴。这些要求不适用于油脂过多会损坏设备的轴承，比如电动机。特殊的润滑配件要在下列情况中使用，即只能由专业受过培训的人员使用恰当的润滑装备完成的情况。

3.23.3 Electrical motors shall include automatic lubrication with pressurized ( and drained) Simalube type grease tank at each fitting. Gantry motors bearings shall be sealed type whenever possible. Hoist, trolley and boom main motors , as well as hydraulic systems , should be greasable as described above .
3.23.3 电动机应包含自动润滑，使用每个配件上耐压的（及泄油的）Simalube类型的油槽。吊架电机轴承应尽可能是均密封类型的。提升电机、台车电机和主电机及液压系统，应如上所述来润滑。

3.23.4 The lubricating fittings of journals or bearings shall be readily accessible . Grease fittings shall be gathered at the same place as much as possible by means of stainless steel tubing for convenient lubrication .
3.23.4 轴颈或轴承的润滑配件应容易获得。为了方便润滑，应用不锈钢管尽可能把黄油嘴聚拢在同一个地方。

3.23.5 Only one size and type of lubricating fitting shall be used except for special equipment as allowd by 3.23.2 above .All fittings shall be plainly visible and accessible .
3.23.5 只使用一种尺寸和类型的润滑装置，除了上面的3.23.2章节所允许的特殊设备。所有这些配件应清楚易见并易于获得。

3.23.6 The Contractor shall furnish and install lubricants and hydraulic fluid in sufficient quantities for initial lubrication of the crane .
3.23.6 承包人要为吊车最初的润滑供给并加注入足够数量的润滑油和液压油。

3.23.7 The crane shall be lubricated with proct of either mobil or shell .
3.23.7 吊车润滑要使用美孚公司或壳牌石油公司的产品。

3.23.8 Oil samples shall be taken from each recer and hydraulic power uint ring field testing . See section 9 .
在实地测试期间，油样要从每个减速机和液压动力单元中提取。参见第9章节。

3.23.9 The Contractor shall provide at crane acceptance a listing of all lubricants installed in the crane .
承包人要在起重机验收中提供所有注入起重机上的润滑油的清单。

10.3 AUTOMATIC LUBRICTION SYSTEM
10.3.1 If this technical option is exercised , a centralized automatic grease lubrication system(s) shall be supplied at the gantry level with the exception of motors and couplings .
10.3自动润滑系统
10.3.1如果执行这些技术附件，应在吊架水平位置提供一个集中自动油脂润滑系统，电机和连接件除外。

10.3.2 The system shall have the following feature :
Dual line
Electric pump
High/Low pressure alarms tied into the CMS
Manual adjustment of indivial lubrication supply rates of each supply point
Stainless steel distribution lines and manifold blocks
Reservoir fill point accessible from ground level
Tank level full/empty signal light next to fill point and tied into the CMS
Sufficient resevior size to minimize refilling frequency
10.3.2该系统有下列特征：
双路
电泵
嵌入CMS系统的高/低压报警
手动调节每个注油点各自的润滑油注入速率
不锈钢分布线和油路块（或称为歧管挡块）
储油箱注油点从地准水平面获取
油箱液位满/空信号灯紧邻注油点并嵌入CMS系统
充裕的储油箱尺寸以使重注油频率减到最小

10.3.3 The Bidder’s Proposal shall contain a full description of the system offered .
投标人的提案应包含关于所供应系统的详尽描述。

10.3.4 The system shall be subject to the Engineer’s approval .
该系统将取决于工程师的认可。

注：
3.23.3处：
Simalube是瑞士的一家注油器等产品的生产商。
Hoist, trolley and boom main motors因不是很熟悉你这种起重机，故此处这几个电机用途不是特别明白。应根据你的设备来定名。
10.3.2处：
CMS：照文章中看来，应该是计算机监控系统，或之类的控制系统。

这段文章应该是取自起重机采购协议或合同中关于润滑的部分章节，大体意思应该差不多。你再参照你熟悉的设备来进行小幅修改即可。

段落不算短啊，应该多加分才是的哦:)

㈣ 英语高手，帮忙翻译两句话，谢谢

你好，我的名字叫比尔，我想知道硅粉在摩擦电序中的位置。

我正在试着用摩擦电子探测器来探测粒子。所以我想知道硅粉在摩擦电序中的位置。

衷心感谢你的帮助。

㈤ 英文翻译 帮下忙

开动引擎或移动齿轮、驱动必须降低离合器
在传输中解脱的目的与发动机那时,
驱动连接到传递成员要么是固定或输入轴旋转速度慢,艾比驾车成员或者连接到发动机曲轴没有春天压在离合器总成零件所以没有摩擦传动成员和driben成员当司机让松散的离合器,弹簧压力增加的离合器部件摩擦部分也增加了由弹簧施加压力的成员是由驱动的驱动通过离合器和连接积极的,是由会员间的摩擦表面的成员当全部弹簧压力、转速的驾驶和推动会员应当是相同的此时此刻,离合器必须作为一种固耦合装置和传送所有引擎动力传动、式。

㈥ 工业上的”摩擦片”用英语怎么说friction plate 还是friction disk．

friction
plate
disk是磁盘的意思所以不对的！
再看看别人怎么说的。

㈦ 英文翻译 关于机械零件摩擦失效分析

Abstract: The failure of the machinery wear and tear of Damian wide abrasion failure, citing the drawing Carbide Die wear failure of the case, the final discussion of the wear failure analysis should pay attention to some of the problems,
Key words: abrasion; failure; mechanical procts; Case Study

㈧ 简易装置 英语怎么说

simplified facility

㈨ 请英语达人帮忙翻译一下，谢谢！

The specific situation is this: yesterday I have sent email to ship company booking, today the factory told packing list information wrong, party number changed. Now I need to send mail to booking, and explain the reason.
General meaning is as follows: because I the factory to provide copies of packing list before information is wrong, I enclose updated booking, please provide housing paper as soon as possible.
希望能帮到您，我建议您以后想翻译可以直接去有道，网络搜有道，第一个就是，不用等大家帮您。节省时间吗。

㈩ 耐摩擦色牢度的英语翻译 耐摩擦色牢度用英语怎么说

耐摩擦色牢度
[化]color fastness to rubbing; colour fastness to rubbing