空载变速英语怎么说及英文翻译
Ⅰ 翻译成英文
1、悬挂点焊机 Suspension Spot Welding Machine
2、型号Model
3、电源电压Power Supply
4、额定容量Rated Capacity
5、额定负载持续率Rated Duty Cycle
6、最大焊接功率Maximum Welding Power
7、次级空载电压Secondary Unload Voltage
8、绝缘等级nsulation Level
9、冷却水流量Cooling Water Flow Rate or Chilled-water Flow Rate
Ⅱ 变压器专业英语翻译，跪求各位英语达人翻译。
Roll the sealed type distribution transformer core is developed in recent years, the new generation of low noise, low loss, and its core transformer no juncture, rece no-load loss and no-load current no-load current, high ~ 80%, 60% lower in iron wire wound on continuous windings, tight, concentricity well. Noise dropped 10 decibels. Due to the continuous winding, iron makes full use of the manufacturing of sexual orientation, no-load loss reced by 20% ~ 30%, is a new generation of high-tech energy-saving and environmental protection procts.
The sealed type distribution transformer USES don't hang core structure, make internal and external tank completely isolated, no storage cabinets, the thermal changes in transformer tank operation by elastic corrugated chips to make compensation for expansion, transformer oil and insulation parts with outside air, water, and the separation of transformer oil and slow the aging in insulation parts. Seal of high fuel oil resistant balata, but not in the circumstance that hang core inspection operation for 20 years, rece operation maintenance cost, be helpful for the inconvenience. Some maintenance
The new type S9 oil-immersed three-phases transformer USES unified design standards, advanced and reasonable structure, insulation resistance short-circuit capacity is strong, its performance achieved the international similar proct level, with S7 procts, on average, no-load loss dropped by 10.25% no-load current decline 37.7%, load loss and lower average 22.4% appearance, reasonable structure according to user's chip and tank can tubular radiator, in recent years is one of the most widely used energy saving procts.
Developed SC9 series of epoxy resin casting dry-type power transformer and air insulated SG type dry type transformer insulation resistance short-circuit capacity, good performance, high impact resistance level of lightning. Epoxy resin casting dry-type distribution transformer winding high by epoxy resin casting seal, adoption of epoxy resin performance is good, crack, high temperature resistant, high mechanical strength, long service life. Flame retardant, moistureproof, explosion-proof pollution-free.
Procts, small volume, low noise. The winding in the operation of automatic temperature monitoring and are protected alarm device. In the forced air cooling can make the rated capacity over 40%. Can be widely used in high-rise buildings, station, wharf, subway, airport, power transmission and distribution system is the important place.
Combined-type distribution transformer (American box variable) is a new body, transformer switch, fuse, tap-changer and relevant auxiliary equipment in one of the transformer. With all its insulation, seal structure, and adopt double welding wire protection. Transformer core adopts special structure, low consumption, low noise, no heat, lightning case. High-pressure line adopts elbow joint, can operate cable 200A load current, can be done in an emergency operation, load switch with isolation switch features. Combined transformer, compact structure, small volume, cover an area of an area small, less investment, easy to install and can be widely used in airport, high-rise buildings, business center, dweller, streets, can further load center installation. When ordering, please indicate the combined transformer or terminal type ring network.
SZ type power transformer on-load changer, in use process for saving transformer on-load changer with reliable quality, reasonable, accord with national economic indicators GB1094-1996 power transformer and GB/T6451-1999 "three-phase oil-immersed transformer, electric technical parameters and requirements. Core adopts the high quality manufacturing, advanced proction technology, Oil and winding road structural design is reasonable, high mechanical strength and resistance short-circuit capacity is strong, beautiful generous.
仅作参考
Ⅲ 请帮我翻译，专业英语
在环境温度下，应能于30s内起动成功。
should be able to start up successfully within 30 seconds at ambient temperature.
在允许的工作环境温度运行停机后，应能于30s内重新起动成功。
should be able to re-start successfully within 30 seconds when stopped at operating ambient temperature.
送检样机经检验, 健康与安全基本要求除标志（无制造年份），其余项目与欧盟 98/37-EC机械指令一致。
The submitted prototype has been inspected , the health and safety, and other items apart from the mark (no manufacturing time) conform to the basic requirements of EU Machinery Directive 98/37-EC.
燃油消耗率 specific fuel consumption，
常温起动 cold starting，
热起动 hot starting，
稳定调速率 steady state speed governing rate，
最大扭矩及转速 maximum torque and speed，
最低空载稳定转速 minimum no-load steady speed，
最低空载稳定转速波动率 fluctuation ratio of minimum no-load steady speed.
Ⅳ 哪位达人大哥,帮小妹翻译一下这些专业名词吧,我在这里向各位达人致敬了!!
楼上从网上拷贝那么多有什么用？误人啊！
还不如实实在在地帮人翻译一下：
（本人在外企车间干过，这些工具的英文名是常用的）
电动工具枪Electric Tool Gun,螺丝头Screw Head,螺丝刀Screw Driver,台钳Bench Clamp,半圆挫Half Round File,半圆铲Half Round Scraper,大力钳Heavy Tong,螺母Nut,外钣手Outside Spanner,内钣手Inside Spanner,喉钳Throat Tong,拉尺Tape Measure,钳子Pliers,螺丝刀Screw Driver,电钻Electric Drill,冲击钻Hammer Drill,扳手Wrench,尖嘴钳子Nose Pliers,夹板Splint,蟹叉Crab Fork,内六角扳手Allen Wrench,喉夹Throat Clamp,圆挫刀 Round File,扁形挫刀Flat File,长角铁Long Angle Iron,中角铁 Middle Angle Iron,小角铁Small Angle Iron,紧固片Fitting Fastening
Ⅳ 维修工具的英语翻译
一画
一字螺丝批 slot type screwdriver
一点透视 one-point perspective
二画
二合一黏合剂 epoxy resin adhesive
二合胶；混合胶 epoxy glue
二维的；平面的 two-dimensional
二进制 binary
二极管；整流子 diode
二号螺丝攻 second tap
二路开关 two-way switch
十进制的；公制的 metric
人工制品 artefact
人造板 man-made board
人体工程学 ergonomics; human engineering
人体尺寸 human dimension
人体测量学 anthropometry; anthropometrics
刀片 blade
刀身 blade
刀具 tool
刀具溜座 carriage
刀柱 tool post
刀架 tool rest
刀架底座 tool rest bracket
刀座帷；床鞍 apron
刀座鞍；溜板座 saddle
力 force
力三角形 triangle of force
力平行四边形 parallelogram of force
力多边形；多边形力学 polygon of force
力的分解 force resolution
力架；亮漆 lacquer
力矩 moment
力偶 couple
力矩定律 law of moment
力-距离图表 force-distance graph
力图 force diagram
力线 line of force
力点 effort
十字榫 cross halving joint
十字螺丝 Philip's head screw
十字螺丝批 Philip's type screwdriver
丁字尺；T 尺 tee square
三画
三爪夹头 three-jaw chuck
三角尺 set square
三角形结构系杆 triangulation tie
三角锉 triangular file
三维的；立体的 three-dimensional
三氯甲烷；哥罗芳 chloroform
三聚氰胺；蜜胺 melamine
三点透视 three-point perspective
上油漆 painting
上釉 enamelling
凡立水 varnish
叉形顶尖 fork centre
口罩 mask
士力；虫漆 shellac
士巴拿；扳手 spanner
大芯夹板；宽条芯夹板 blockboard; solid corestock-laminated board
大量制造 mass proction
子口刨；槽口刨；边刨 rebate plane
小型平槽刨 miniature router plane
小型线料弯曲器 small wire bender
小型弯折机 mini bender
小型电路断路器；跳菲 miniature circuit breaker (MCB)
小齿轮 pinion
山樟 San Cheong
工件 workpiece
工字梁 I beam
工作面 working surface
工作图；制作图 working drawing
工作台 bench; working table
工具 tool
工具贮存室 tool storage
工具槽 well
工具钢 tool steel
工场 workshop
工场安全 workshop safety
工程字书写技巧 lettering
工程系统 engineering system
工程绘图 engineering drawing
工业酒精；火酒 methylated spirit
弓形手钻；手摇曲柄钻 brace
弓形手钻嘴 brace bit
弓锯 bow saw; hacksaw
弓锯片 hacksaw blade
弓锯床 hacksawing machine
四画
不平衡 imbalance
不含铁金属；非铁金属 non-ferrous metal
不贯穿孔；闭孔；盲孔 blind hole
不贯穿鸠尾榫 lapped dovetail joint
不对称 asymmetry
不锈钢 stainless steel
不稳定平衡 unstable equilibrium
中心 centre
中心线 centre line
中心冲 centre punch
中心钻 centre drill
中心钻嘴 centre bit
中央处理器 central processing unit (CPU)
中性 neutral
中性平衡；随遇平衡 neutral equilibrium
中性轴 neutral axis
中密度纤维板 medium density fibre board (MDF)
中粗锉纹 second cut
中碳钢 medium carbon steel
中线 neutral wire
互补金属氧化物半导体 complementary metal oxide semiconctors (CMOS)
介子；垫片 washer
介指铁 ring mandrel
介电常数；电容率 permittivity
介稳态的；亚稳态的 metastable
内力 internal force
内卡尺 inside calipers
内能 internal energy
内涵性质 intensive properties
内圆弯凿 scribing gouge
内锁式配件 interlocking fitting
内燃机 internal combustion engine
内螺纹制造法 tapping
内螺丝 internal thread
内弯边 concave edge
六角金属枝 hexagonal bar
六角匙 Allen key
六角头螺丝 hexagonal head screw
公制的；十进制的 metric
公差 tolerance
冗余构件 rendant member
分力 component force
分子 molecule
分子力 molecular force
分切；分割；切断 parting off
分贝 decibel
分析 analysis
分析及批判学 analytical and critical studies
分析器 analyzer
分流器 shunt
分界面；界面；接口 interface
分厘卡 micrometer
分规 divider
分割车刀架 parting tool holder
分解 decomposition
分压器 potential divider; voltage divider
隔离开关 isolating switch
切削工具 cutting tool
切削液 cutting fluid
切削深度 depth of cut
切屑；碎屑 chip
切线锯法 tangential sawing
切辊纹；滚纹 knurling
切断；分切；分割 parting off
切断工具 parting tool
勾；勾脚 hook
勾刀；胶片刀 plastic cutter
化胶水 tensol
反向偏压 reverse biased
反相放大器 inverting amplifier
反相器 inverter
反射 reflection
反电动势 back e.m.f.
反馈；回输 feedback
天拿水；稀释剂 thinner
天梯牙；齿条 gear rack
天然木材 natural timber
天然干燥法 air seasoning
孔隙率 porosity
尺寸 dimension
尺寸线 dimension line
尺身 blade
引力；重力 gravitational force
心形凸轮 heart-shaped cam
心材 heartwood
心轴 mandrel
心销 core pin
手工具 hand tool
手工锯 junior hacksaw
手削法 paring
手持虎钳 hand vice
手柄 handle
手套 gloves
手扫漆 brushing lacquer
手推车 barrow
手提式竖线锯 portable jigsaw
手提电动工具 portable power tool
手提电钻 electric hand drill
手进给 hand feed
手摇曲柄钻；弓形手钻 brace
手摇钻 hand drill
手锉 hand file
手锯；板锯 handsaw
手锥 bradawl
手辘轧机 hand rolling machine
支柱；支撑物 strut
支架；支座 support
支点 fulcrum; pivot
文字 text
方向 direction
方向针 pointing needle
方枝 square bar
方波形 square waveform
方波产生器 squarer
方型牙板 rectangular die
方格纸；网格纸 grid paper
方通 square tube
方块图 block diagram
方锉 square file
方头钻嘴 square shank bit
方螺帽 square nut
方边凿；直边凿 firmer chisel
木 wood
木工 woodwork
木工工作间 woodwork area
木工工作台 woodworker's bench
木工车床 wood turning lathe; woodworking lathe
木工铅笔 carpenter's pencil
木工刨床 thicknessing and planning machine
木牙螺丝；木螺钉 wood screw
木材 timber
木材车削 wood turning
木材车削工具 wood turning tools
木屑压合板；万花板 chipboard
木条接榫 corner strip joint
木圆头槌 doming mallet
木模；模型 patterns
木线 wood strip
木胶粉 ureaformal dehyde resin glue
木锉 rasp
木螺钉；木牙螺丝 wood screw
木槌 mallet
止推轴承 thrust bearing
止推垫圈 thrust washer
比例 proportion
比例尺 scale
比例常数 proportionality constant
比例极限 proportional limit
比较器 comparator
比热容量 specific heat capacity
水平投影面 horizontal plane
水平仪；平水尺 spirit level
水气掣；漏电断路掣 earth leakage circuit breaker (ELCB)
水晶胶；聚酯树脂 polyester resin
水晶胶的铸造成形 resin casting
水磨砂纸 silicon carbide paper
火叉 firing fork
火水；煤油 kerosene
火牛；变压器 transformer
火石轮 grinder
火花电蚀法；放电极加工 electrical discharge machining
火酒；工业酒精 methylated spirit
火钳 tongs
火线；活线 live wire
火砖 fire brick
爪扣；爪形离合器；犬齿式离合器 dog clutch
牙板；丝模 die
牙板扳手；丝模扳手 die holder (stock)
牙板螺帽 die nuts
牛皮胶；动物胶 animal glue
牛油纸 tracing paper
牛顿运动定律 Newton's laws of motion
犬齿式离合器；爪扣；爪形离合器 dog clutch
五画
丙烯;丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS)
主轴；心轴 spindle
主题 motif
令(纸张的计数单位) ream
凹座 recess
凹模 hollowing block
凸缘 flange
凸缘联轴节 flange coupling
凸轮 cam
凸轮式配件 cam-action fitting
凸轮传动 cam drive
凸头螺丝 raised head screw
加成作业；添加法 addition process
加油 oiling
加速器 accelerator
功能；用途 function
功率因子 power factor
功率放大器 power amplifier
功率板 power amplifier board
功率晶体管 power transistor
包氏记号法 Bow's notation
「包浩思」；「包豪斯」〈设计风格) Bauhaus
半永固法；半永久接合 semi-permanent joining
半接榫 halving joint
半闭式槽榫 stopped housing joint
半圆(木)锉 half-round rasp
半圆车刀 turning gouge
半圆锉 half-round file
半圆头铆钉 snap rivet
半导体 semiconctor
卡路里；卡(热量单位) calorie
卡纸 card paper
卡尺；测径器 calipers
去角；倒角 chamfer
可切削性 machinability
可行性 feasibility
可逆过程 reversible process
可压缩性 compressibility
可变电阻 variable resistor
四分仪 quadrant
四爪夹头 four-jaw independent chuck
四圆心法(绘图) four-centre method
外卡尺 outside calipers
外形塑造 shaping
外形线；轮廓线 outline
外推法 extrapolation
外圆弯凿 firmer gouge
外螺纹 external thread
外螺纹制造法 threading
外弯边 convex edge
外观 appearance
失真 distortion
尼龙；聚醯胺 nylon; polyamide (PA)
尼龙墨水针笔 technical felt-tip pen
左右调校杆 lateral adjusting level
市售尺寸；标准尺寸 stock size
市电频率；电源频率 mains frequency
平(木)锉 flat rasp
平水尺；水平仪 spirit level
平行投影 parallel projection
平行车削 parallel turning
平行虎钳 parallel vice
平行钉法 parallel nailing
平底弯刨 flat faced spokeshave
平底钻嘴 forstner bit
平板结构 slab construction
平流扼流圈；滤波扼流器 smoothing choke
平流电容器；滤波电容器 smoothing capacitor
平流电路；滤汳电路 smoothing circuit
平面板；正台 surface plate
平面图；俯视图 plan
平面锤 flatter
平移 translation
平搭榫 corner halving joint
平嘴钳 flat nose pliers
平槽刨 router plane
平衡 balance; equilibrium
平衡力 equilibrant
平衡条件 equilibrium condition
平衡电桥 balanced bridge
平头弧刀 square nose gouge
幼纹 smooth cut
打凹成形 hollowing
打凸成形 raising
打槽机 routing machine
打线；打槽 routing
打磨 fitting; polishing
打磨机 polisher
本生灯 Bunsen burner
本征半导体 intrinsic semiconctor
正反器；触发器；复振器 flip-flop
正反馈；正回输 positive feedback
正火 normalizing
正向偏置 forward bias
正投影 orthographic projection
正投影图 orthographic drawing
正弦波形 sinusoidal waveform
正面投影 front projection
正视图 elevation; front elevation
正极；阳极 anode
正齿轮 spur gear
正台；平面板 surface plate
永久性接合 permanent joining
瓦通纸；瓦楞纸板 corrugated board
生长层 cambium layer
生产图 proction drawing
生胶浆 rubber cement
生钢；铸钢 cast steel
生铁；铸铁 cast iron
用途；功能 function
白杨木 poplar
白胶浆 PVA glue; white glue
皮沙垫 leather sandbag
皮革 leather
皮革黏合剂 leather glue
皮鞋 leather shoes
目录 contents
矢量；向量 vector
石灰岩 limestone
石英晶体振荡器 quartz crystal oscillator
石棉 asbestos; asbestus
石膏 Plaster of Paris
示波器 oscilloscope
立体图 pictorial drawing
六画
交流电流 alternating current (a.c.)
交流电压 a.c. voltage
交联结构 cross-linked structure
仿饰金 gilding metal
伏特 volt
光力架 clear lacquer
光拉软钢 bright drawn mild steel (B.D.M.S.)
光敏电阻 light dependent resistor (LDR)
光测弹性学 photoelasticity
光刨；滑刨 smoothing plane
光电效应 photoelectric effect
光泽 lustre
全闭式槽榫 closed housing joint
共面力 coplanar force
共聚合作用 co-polymerization
共聚物 copolymer
共价键 covalent bond
共振；共鸣；谐振 resonance
印刷电路板 printed circuit board (PCB)
同素异形 allotropy
同轴电缆 coaxial cable
同温 equality of temperature
向量；矢量 vector
向量和 vector sum
合力 resultant force
合口扁钳 close mouth tongs
合成色；等和色 secondary colour
合成品 composite
合成粅料 composite material
合金 alloy
合金工具钢 alloy tool steel
合钉；定位销 dowel
回火 tempering
回复力 restoring force
回复力偶 restoring couple
回弹 resilience
回输；反馈 feedback
地线 earth wire
多刃切削刀具 multi-point cutter
多孔塑料；泡沫塑料；海绵状塑料 foam plastics
多方榫接合 pinned joint
多媒体 multi-media
多晶性 polycrystallinity
多谐振动器；多谐振荡器 multivibrator
多边形力学；力多边形 polygon of force
字母冲 letter punch
字板 letter stencil
安全 safety
安全守则 safety rule
安全系数 safety factor
安全措施 safety precaution
安全眼罩 safety goggle
安全设备 safety equipment
安全药箱 safety box
安培 ampere
安培计；电流表 ammeter
尖脚 spur
年轮 annual ring
成本 cost
成形 forming
扣件；击固件 fastener
扣钉 clout nail; cramp
托架 bracket
收缩 shrinkage
曲柄 crank
曲柄轴 crank shaft
曲线规；云板；云尺 French curve
有效的 efficient
有效电流 effective current
灰；灰末 ash
百折胶；百折胶；聚丙烯 polypropylene (PP)
竹 bamboo
羊角锤 claw hammer
老化 ageing
肋条 rib
肌理；质感；质地 texture
自由度 degree of freedom
自动控制 automatic control
自动进给 auto-feed
自然干燥法 natural seasoning
自感量 self-inctance
自感应 self-inction
色彩；颜色 colour
色调 tone
色环 colour wheel
行星齿轮；周转齿轮 epicyclic gear
七画
肘节开关 toggle-switch
串激电动机；串绕电动机 series-wound motor
位能；势能 potential energy
位梯度；势梯度 potential gradient
位移 displacement
位错 dislocation
伸长度 elongation
作工硬化 work hardening
作功 work done
作图线 construction line
低密聚乙烯 low density polyethylene (LDPE)
低通滤波器 low-pass filter
低电压 low voltage
低碳钢 low carbon steel
布置 layout
免油轴承 oil-less bearing
冷加工；冷作工 cold working
冷加工硬化 cold work hardening
冷色 cool colour
冷轧压 cold rolling
冷却系统 cooling system
冷却效应 cooling effect
冷却液流量 coolant rate
冷凝胶；环氧树脂 epoxy resin
利口；「披」口；铁屑 burr
刨平 planing
刨花板；碎料板 particle board
吹风机 air blower
吹气模塑；吹模塑 blow moulding
吹管 blow pipe
含铁金属 ferrous metal
含水量 moisture content
坑凿 cross-cut chisel
均方根值 root mean square value
均角投影图；等角投影图 isometric drawing
均速圆周运动 uniform circular motion
夹；夹钳 clamp
夹 cramp
夹卡 mounting board
夹具 fixture; jig
夹具及固定装置 jig and fixture
夹板；胶合板 plywood
夹持工具 clamping device; holding tool
夹背锯；榫锯 tenon saw
夹头 chuck
夹头开启匙；夹头扳手 chuck key
夹迭黏合成形 lamination
尾座 tailstock
床身；床道 lathe bed
床鞍；刀座帷 apron
形心；面心 centroid
形状 shape
形变 deformation
「快把」板；硬质纤维板 hardboard
快速移位 rapid traverse
抗扭强度 torsional strength
抗屈强度 bending strength; yield strength
抗性分量；无功分量 reactive component
抗拉强度 tensile strength
抗氧化剂 anti-oxidant
抗剪强度 shearing strength
抗磁性物料 diamagnetic material
抗挠性 stiffness
抗压强度 compressive strength
抗断强度 breaking strength
技术员；技师 technician
扶架 steady
扭力 torsion
扭矩；转矩 torque
扭转 torsion
扭转角 angle of torsion
把手 hand grip
扼流圈 choke
扳手 spanner; wrench
投影 projection
投影面 projection plane
投影线 projection line
攻丝 tap
材料 material
材料单；材料表 material list
杜拉铝 ralumin
杉木 spruce
步进电动机 stepper motor
步冲轮廓法 nibbling
每分钟转数 revolution per minute (r.p.m.)
系统组件 system component
角托架 angle bracket
角位移 angular displacement
角板；直角板 angle plate
角度 angle
角榫 corner angle joint; corner joint
角铁 angle iron
谷巴凡立水 cobal varnish
车刀架 tool holder
车床 lathe
车床工具 lathe tools
车床中心钻咀 lathe centre bit
车床操作法 lathe operation
车削；车旋 lathe turning; turning
车削工具 turning tools
防火胶板 Formica
防锈 rust prevention
防声耳筒；护耳器 ear-protector
防松螺帽 lock nut
防护装置；保护罩；保护网 guard; safety guard
八画
注射成形法；喷射铸造法 injection moulding
并激电动机；并绕电动机 shunt-wound motor
奶酪胶 casein glue
乳胶漆 emulsion paint
亚加力；压克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA)
亚稳态的；介稳态的 metastable
来回摆动 oscillating
两点透视 two-point perspective
刻度；划线 ruling
刺冲 dot punch
刮刀 scraper
刮擦 scraping
制动鼓 drum brake
制动碟 disc brake
制动器 brake
受迫振动 forced vibration
受迫振荡 forced oscillation
和谐 harmony
周转齿轮；行星齿轮 epicyclic gear
固定夹；台夹 bench holdfast
固定负载 dead load
定子 stator
定位销；合钉 dowel
定位螺丝 set screw
定距轮 stitch marker
屈片机 folding machine
屈曲 bending
屈服点；降服点 yield point
屈圈法 loop forming
屈卷法 scrolling
屈接缝 folded lap seam
屈喉机 tube bender
屈折 folding
屈折线 folding line
屈压接缝 folded & grooved seam
延性 ctility
延性的 ctile
弦锯法 plain sawing
弧口凿；圆凿 gouge
往复式运动 reciprocatory motion
拉力 tensile force
拉力计；张力计 tensiometer; tensometer
拉钉 blind rivet; pop rivet
拉钉接合 blind riveting; pop riveting
拉钉钳 blind riveting pliers; pop riveting pliers
拉张 tension
拉张应力 tensile stress
拉张应变 tensile strain
拉细 drawing-down
拉制法 drawing
拉线 wire drawing
「披」口；利口；铁屑 burr
拔钳 nippers
抛光 buffing
抛光机 buffing machine
放大；扩大 enlargement
放大尺 pantograph
放大倍数 amplification factor
放大器 amplifier
放电极加工；火花电蚀法 electrical discharge machining
易用万能尺 line setter
易碎 fragile
〈绘画的〉明暗运用；描影 shading
枝；杆 rod
杯形顶尖 cup centre
杯头螺丝 hexagonal socket head cap screw
板锯 panel saw
松木 pine
松节水 turpentine
法式磨光 French polishing
法拉〈电容量单位〉 farad
油石；磨刀石 oil stone
油漆；涂料 paint
泡沫塑料；多孔塑料；海绵状塑料 foam plastics
物理特性 physical property
物理属性 physical attribute
物理量 physical quantity
盲孔；闭孔；不贯穿孔 blind hole
直尺 ruler; straight rule
直角叉榫 corner bridle joint
直角尺 try square
直角板；角板 angle plate
直角杠杆 bell crank lever
直身钻嘴 straight shank drill
直车刀架 straight tool holder
直流发电机 d.c. generator
直流电流 direct current (d.c.)
直流电动机；直流马达 d.c. motor
直纹锯 rip saw
直线切削 linear interpolation
直线运动 rectilinear motion
直边凿；方边凿 firmer chisel
直铁剪 straight snips
硅 silicon
空行程 idle stroke
空气动力学 aerodynamics
空间 space
空载 no load
花纹凿 embossing stamp
花梨木 rosewood
花样；图案 pattern
虎克定律 Hooke's Law
虎钳 vice
虎钳护罩 vice clamp
初步意念 proposed solution
表面 surface
表面展开图 surface development
表面张力 surface tension
表面处理 surface finishing; surface treatment
表面硬化 case hardening
表面硬化钢 case-hardened steel
表达方式 presentation
表达技巧；传意技巧 communication technique
表观膨胀；视膨胀 apparent expansion
金工 metalwork
金工工作间 metalwork area
金工角尺 engineering square
金工车床 metalwork lathe
金工虎钳 engineer's vice
金工锯床 power hacksaw
金属包头；金属箍 ferrule
金属配件 metal fittings
金属线 wire
金属压展机 hand rolling mill
金属擦光剂；磨光剂 metal polish
金属薄片 sheet metal
金属键 metallic bond
长方通 rectangular tube
长刨 trying plane
长螺旋钻咀 long auger bit
长镗孔 long boring
闸极 gate
阻抗 impedance
附件 attachment
附录 appendices
青铜 bronze
非反相放大器 non-inverting amplifier
非本征半导体 extrinsic semicon
慢慢找吧,下面个网站是汽车专业词汇,可以去找找
Ⅵ 物流海运专用术语<英语》
看看如下的内容吧:
A
alongside -- The side of a vessel.
B
barrel -- A measurement term that refers to 42 gallons of liquid at 60 degrees Fahrenheit (15.56 degrees Celsius).
berth -- The structure where a vessel is secured for the loading and unloading cargo.
bonded warehouse -- A warehouse authorized by customs authorities for the storage of goods on which payment of ties is deferred until the goods are removed.
bow -- The front of a vessel. Also see "stern."
breakbulk cargo -- Loose, non-containerized procts. Examples include steel slabs and coils.
bulk cargo -- Loose cargo shipped in the cargo hold of a vessel without mark and count. Examples include coal, grain and sulfur.
bunker -- A maritime term that refers to fuel used aboard a vessel.
C
cargo -- Freight loaded into a vessel.
cargo manifest -- A list of all cargo carried on a specific vessel voyage.
cargo tonnage -- Most ocean freight is billed on the basis of weight or measurement tons (W/M). Weight tons can be expressed in short tons of 2,000 pounds, long tons of 2,240 pounds or metric tons of 1,000 kilos (2204.62 pounds). Measurement tons are usually expressed in cargo measurements of cubic feet (one cubic foot equals 0.03 cubic meters) or cubic meters (one cubic meter equals 35.31 cubic feet). Typically, 40 cubic feet (1.13 cubic meters) is the measurement standard.
carrier -- Any person or entity who, in a contract of carriage, undertakes to perform or procure the performance of carriage by rail, road, sea, air, inland waterway or by a combination of such transportation modes.
chassis -- A frame with wheels and container-locking devices in order to secure the container for movement.
container -- A truck trailer body that can be detached from the chassis for loading into a vessel, a railcar, or stacked in a container depot. Containers may be ventilated, insulated, refrigerated, flat rack, vehicle rack, open top, bulk liquid or equipped with interior devices. A container may be 20 feet (6.1 meters), 40 feet (12.19 meters), 45 feet (13.72 meters), 48 feet (14.63 meters) or 53 feet (16.15 meters) in length, eight feet (2.44 meters) or eight feet, six inches (2.59 meters) in width, and eight feet, six inches (2.59 meters) or nine feet, six inches (2.9 meters) in height.
container freight station (CFS) -- A shipping dock where cargo is loaded ("stuffed") into or unloaded ("stripped") from containers. Container reloading from/to rail or motor carrier equipment is a typical activity.
container terminal -- An area designated for the stowage of cargo in containers. Usually accessible by truck, railroad and marine transportation, the terminal is where containers are picked up, dropped off, maintained and stored.
containerization -- Stowage of general or special cargo in a container for transport in various modes.
containerload -- A cargo load sufficient in size to fill a container either by cubic measurement or by weight.
container port -- A seaport that features cargo terminals developed specifically to handle marine cargo containers.
D
dock -- For ships, a cargo-handling area where a vessel normally ties up. For land transportation, a loading or unloading platform at an instrial location or carrier terminal.
doublestack train -- A train using specialized railcars that enable marine cargo containers to be stacked one atop another.
draft -- The number of feet (or meters) that the hull of a ship is beneath the surface of the water.
dry bulk container -- A container constructed to carry grain, powder and other free-flowing solids in bulk. Used in conjunction with a tilt chassis or platform.
dry cargo -- Cargo that is solid in nature and normally does not require temperature control.
E
export -- Shipment of goods to a foreign country.
F
feeder service -- Cargo to/from regional ports are transferred to/from a central hub port for a long-haul ocean voyage.
feeder vessel -- A short-sea vessel that transfers cargo between a central hub port and smaller spoke ports.
FEUs -- Maritime abbreviation for "40-foot equivalent units," which refers to containers that are 40 feet (12.19 meters) in length. One FEU is equal to two TEUs, or "20-foot equivalent units." See "TEUs."
flat car -- A railcar without a roof and walls.
flat rack/flat bed container -- A container with no sides and frame members at the front and rear for cargo loading from the sides and top.
foreign-trade zone -- A free port in a country divorced from Customs authority but under government control. Merchandise, except that which is prohibited, may be stored in the zone without being subject to import ty regulations.
free port -- A restricted area at a seaport used for the handling of ty-exempt import goods.
freight -- Refers to either the cargo carried or the charges assessed for carriage of cargo.
freight forwarder -- A person whose business is to act as an agent on behalf of the shipper. A freight forwarder frequently makes the booking reservation.
G
gateway -- A point at which freight moving from one territory to another is interchanged between transportation lines.
gross weight -- The entire weight of goods, packaging, container and freight car, ready for shipment. Generally, the combined weight limit of the cargo, container and tractor for highway transport is 80,000 pounds (36,287.39 kilograms).
H
hatch -- The opening in the deck of a vessel, providing access to the cargo hold.
I
import -- Shipment of goods from a foreign country.
inland carrier -- A transportation line that hauls export or import traffic between ports and inland points.
intermodal -- A shipping term denoting the interchangeable movement of cargo containers between different modes of transportation, primarily ship, truck and train, where the equipment is compatible with the multiple transport systems.
J
Jacob's ladder -- A rope ladder suspended from the side of a vessel that is used for boarding.
just in time (JIT) -- In this method of inventory control, warehousing is minimal or non-existent: The container is a "movable" warehouse and must arrive neither too early nor too late
K
knot -- One knot is equal to one nautical mile (6,076 feet or 1,851.96 meters) per hour. In the early sailing days, speed was measured by tossing overboard a log secured by a line. Knots were tied into the line at intervals of approximately six feet (1.83 meters). The number of knots measured was then compared to the time required to travel the distance of 1,000 knots in the line.
L
laden -- Loaded aboard a vessel.
landbridge -- The movement of cargo, by water, from one country through the port of another country, by rail or truck, to an inland point in that country or to a third country. For example, cargo from Japan is landbridged across the United States to France.
liquid bulk -- Cargo that is fluid in nature and typically transported in tankers. Examples include oil and other petroleum procts.
longshoreman -- An indivial employed in a port to load and unload cargo vessels.
loose -- Without packing.
M
maritime -- Business pertaining to commerce or navigation transacted upon the sea or in seaports.
meter -- One meter is equal in length to 3.28 feet or 39.37 inches.
metric ton -- One metric ton is equal in weight to 2,204.62 pounds or 1,000 kilograms.
mile -- One mile is equal to 5,280 feet or 1.61 kilometers on land. Also see "nautical mile."
mini-landbridge -- An intermodal system for transporting containers by ocean and then by rail or motor to a port previously served as an all-water move. For example, cargo from China is mini-landbridged through Seattle to New York.
multimodal -- Synonymous with "intermodal" for all practical purposes.
N
nautical mile -- One nautical mile is equal in length to 607,612 feet or 1.85 kilometers, which is the distance of one minute of longitude measured at the equator. Also see "mile."
near-dock railyard -- A cargo facility used primarily to sort marine cargo containers and assemble into trainloads bound for common destinations. These railyards are located inland, in close proximity to a port waterfront.
non-vessel operating common carrier (NVOCC) -- A cargo consolidator in ocean trades that will buy space from a carrier and subsell it to smaller shippers. The NVOCC concts itself as an ocean carrier, except that it will not provide the actual ocean or intermodal service.
O
on-dock railyard -- A cargo facility used primarily to sort marine cargo containers and assemble them into trainloads bound for common destinations. These railyards are located on a port waterfront.
origin -- The location where a freight shipment begins its movement.
overheight cargo -- Freight that is more than eight feet high, or too tall to fit into a standard container.
P
pallet -- A platform with or without sides, on which a number of packages or pieces may be loaded to facilitate handling by a forklift or similar functioning equipment.
pier -- The structure where a vessel is secured for the loading and unloading cargo.
piggyback -- A transportation arrangement whereby truck trailers and their loads are carried and moved by train to a destination.
port -- There are three common definitions:
1. A harbor with piers or docks.
2. The left side of a ship when facing the bow. Also see "starboard."
3. An opening in a vessel's side, used for handling freight.
port of call -- A port where a vessel discharges or receives freight.
port of entry -- A port where cargo enters a country and is unloaded.
port of exit -- A port where cargo is loaded and leaves a country.
Q
quay -- A structure attached to land to which a vessel is moored. Also see “berth," "dock" and "pier."
R
ramp -- A railroad terminal where containers are received or delivered and trains are loaded or discharged.
reefer -- An instry term for a refrigerated or temperature-controlled container.
relay -- The transfer of containers from one ship to another when both vessels are controlled by the same network (carrier) manager.
revenue ton -- A ton measurement on which shipments are freighted. If cargo is rated as weight or measure (W/M), whichever proces the higher revenue will be considered the revenue ton. Weights are based on metric tons and measures are based on cubic meters. Hence, one revenue ton is equal to one metric ton (2204.62 pounds) or one cubic meter (35.31 cubic feet).
roll-on roll-off (Ro/Ro) -- A method of ocean cargo service using a vessel with ramps, which allow wheeled containers, trailers or vehicles to be loaded and unloaded without the use of cranes.
S
service -- A string of vessels that makes a particular voyage and serves a particular market.
ship chandler -- An indivial or company selling equipment and supplies to ships.
shipper -- The person or company who usually is the supplier or owner of commodities shipped. Also called the consignor.
ships --There are nine basic types of ships:
1. barge carriers -- Ships designed to transport barges.
2. bulk carriers -- All vessels designed to carry bulk cargo, such as grain, fertilizers, ore and oil.
3. combination passenger and cargo ships -- Cargo vessels with the capacity for 13 or more passengers.
4. freighters -- Comprises refrigerated and unrefrigerated breakbulk vessels, containerships, partial containerships, roll-on roll-off vessels and barge carriers.
5. full containerships -- Vessels equipped with permanent container cells for container storage, with little or no space for other types of cargo.
6. general cargo carriers -- This category includes breakbulk freighters, car carriers, cattle carriers, pallet carriers and timber carriers.
7. partial containerships -- Multipurpose containerships with one or more, but not all, cargo compartments fitted with permanent container cells. The remaining compartments are used for noncontainerized cargo.
8. roll-on roll-off vessels -- Specialized ships designed to carry wheeled containers, trailers and vehicles using onboard ramps.
9. tankers -- Ships fitted with tanks for storage of liquid cargo, such as crude petroleum and petroleum procts, chemicals, liquefied gas, wine and molasses.
short ton -- One short ton is equal in weight to 2,000 pounds or 0.91 metric tons.
side loader -- A lift truck fitted with lifting attachments operating on one side for handling containers.
slip -- A ship's berth between two piers.
spreader -- Equipment designed to lift containers by their corner casters.
stack car -- An articulated five-platform railcar that allows containers to be doublestacked one atop another.
stack train -- A rail service whereby railcars carry containers doublestacked on specially operated unit trains.
starboard -- The right side of a ship when facing the bow. Also see "port."
stern -- The end of a vessel. Also see "bow."
stevedore -- A person or company that employs longshore workers and establishes agreements to load or unload ships.
stowage -- A marine term that refers to loading freight into vessels' cargo holds.
straddle carrier -- Mobile truck equipment that is capable of lifting containers within its own framework.
supply chain -- A logistical management system that integrates the sequence of activities from delivery of raw materials to the manufacturer to delivery of the finished proct to the customer. "Just in time" is an example of supply chain management.
T
tariff -- A publication that sets forth the charges, rates and rules of ports and transportation companies.
terminal -- An assigned area where containers are prepared for loading into a vessel, train or truck, or are stored immediately after discharge from the vessel, train or truck.
TEUs -- Maritime abbreviation for "20-foot equivalent units," which refers to containers that are 20 feet (6.1 meters) in length. Two TEUs are equal to one FEU. Also see "FEU."
transship -- To transfer goods from one transportation line to another, or from one ship to another.
turnaround -- In water transportation, the time between the arrival and departure of a ship from a port.
U
unit load -- Packages loaded onto a pallet, in a crate or any other way that enables them to be handled at one time as a unit.
unit train -- A train comprising a specified number of railcars that remain together as a unit until reaching a designated destination.
unitization -- The consolidation of a quantity of indivial items into one large shipping unit to facilitate handling. Also: The loading of one or more large items of cargo onto a single piece of equipment, such as a pallet.
V
vanning -- A marine term for stowing cargo in a container
warehouse -- A place for the reception, delivery, consolidation, distribution and storage of cargo.
W
warehousing -- The storage of cargo.
weights and measures --
1. One cubic meter is equal to 35.31 cubic feet.
2. One long ton, or gross ton, is equal to 2,240 pounds or 1,016.05 kilograms.
3. One measurement ton is equal to 40 cubic feet or one cubic meter.
4. One metric ton, or kilo ton, is equal to 2,204.62 pounds or 1,000 kilograms.
5. One short ton, or net ton, is equal to 2,000 pounds or 907.18 kilograms
Y
yard -- This term commonly refers to a railroad yard with many rail tracks for assembling, storing or switching freight trains.
Ⅶ 几种螺丝刀的英文单词
你好，电动螺丝刀的空载转速
翻译成英语是：idle
speed
of
electric
screwdriver
——————如有帮助请采纳，谢谢。
Ⅷ 英语Empty set怎么翻译
empty set：数学里面集合术语 空集；空集合。
专业术语解释：空集(empty set):约定存在一个没有任何元素的集合,称为空集,记为φ,有时也用{} 来表示.按子集的定义,空集是任何集合的子集。
相关短语：
axiom of empty set空集公理
axiom of the empty set空集公理
non-empty set非空集 ; 非空集合
双语示例：
Startfromscratch: Start .
从头开始：从一组空的条件开始并添加您自己的条件。
This ,so by nothing (oremptysetbyemptyset).
之所以会出现这个问题是由于字段是空的，因此实际上进行的计算是零乘零（或者空集乘空集）。