工作油缸英语怎么说及英文单词

⑴ 各路高手，哪个能提供液压专业英语词汇，包括缸，阀，泵，马达，密封件，连接件等

液压专业英语词汇
acceptable conditions许用工况
actual conditions实际工况
actual force实际输出力
air contamination空气污染
air consumption耗气量
air conditioner unit空气处理单元
air filter空气过滤器
adjustable restrictive valve可调节流阀
amplifier放大器
amplitude ratio幅值比
analogue amplifier模拟放大器
anti-corrosive quality抗腐蚀性
automatic cycle自动循环
axial piston pump轴向柱塞泵
back pressure背压
bladder accumulator气囊式蓄能器
bleed line放气管路
bonded washer组合垫圈
breakout pressure启动压力
butterfly valve蝶阀
cartridge valve插装阀
cavitation气穴
charge pressure充油压力
check valve单向阀
circle循环
circuit diagram回路图
clamper管卡
closed circuit闭式回路
collapse pressure压溃压力
compensator避震喉
composite seal复合密封件
continuous working conditions连续工况
control of pump泵的控制
control console操作台
control panel控制屏
cooler冷却器
counterbalance valve平衡阀
cracking pressure开启压力
cushioning缓冲
cylinder缸
cycling speed循环速度
De-energizing of solenoid 电磁铁释放
density密度
diaphragm valve膜片阀
differential circuit差动回路
differential cylinder差动缸
differential pressure instrument压差计
digital amplifier数字放大器
direction of rotation旋转方向
directly operated type直动式
displacement排量
dither颤振
double-acting cylinder双作用缸
Double throttle check valve 双单向节流阀
drain line泄油管路
drift漂移
drive shaft coupling联轴器
dwell phase停止工步
plex filter双筒过滤器
efficiency效率
effective filtration area有效过滤面积
elastomer seal弹性密封件
elbow弯头
electrical pressure transcer压力传感器
external leakage外泄漏
extend stroke外伸行程
filter pressure drop过滤器压降
fitting；connection接头
fixed restrictive valve固定节流阀
flared fitting扩口式接头
flash point闪点
flexible hose软管
flange connection法兰接头
flange mounting法兰安装
flow-combining valve集流阀
flow control valve流量控制阀
flow control circuit调速回路
flow divider valve分流阀
flow gain流量增益
flow limit流量极限
flow line管路
flow meter流量计
flow pass流道
flow rate流量
Flow valve 流量阀
flower factor流量系数
foot mounting底座安装
force输出力
four-way valve四通阀
free position自由位
frequency response频率响应
function diagram功能图
gate valve闸阀
gear pump齿轮泵
global(ball) valve球阀
graphical symbol图形符号
heat exchanger热交换器
heater加热器
hydraulic lock液压锁紧
hydraulic motor液压马达
hydraulic power流体传动
hydraulics液压技术
hydrodynamics液力技术
hydropneumatics气液技术
hysteresis滞环
hydraulic amplifier液压放大器
hydraulic controlled type液控式
instantaneous conditions瞬态工况
internal leakage内泄漏
inlet pressure进口压力
inced pressure负载压力
kinematic viscosity运动粘度
laminar flow层流
lap遮盖
leakage泄漏
limited conditions极限工况
linearity线性度
linear region线性区
liquid contamination液体污染
liquid level measuring instrument液位计
lubricator油雾气
manually operated type手动式
manifold block油路块
mechanically controlled type机械控制式
mechanical seal机械密封
meter-in circuit进口节流回路
meter-out circuit出口节流回路
Manifold block 集成块
needle valve针阀
neutral position中位
nitrile butadiene rubber；NBR丁腈橡胶
noise level噪声等级
nominal filtration rating公称过滤精度
nominal pressure公称压力
nozzle flapper喷嘴挡板
null bias零偏
null drift零漂
null(quiescent) leakage零位内泄漏
one-way restrictive valve单向节流阀
opening开口
open circuit开式回路
operating conditions运行工况
operating pressure运行压力
outlet pressure出口压力
over lap正遮盖
override pressure调压偏差
override control优先控制
packing seal填料密封
peak pressure峰值压力
phase工步
phase lag相位移
Pilot valve 先导阀
pilot pressure控制压力
pilot-controlled check valve液控单向阀
pilot-operated type先导式
Pilot operated check valve 液控单向阀
piston pump柱塞泵
pilot line控制管路
pipe-work管路布置
piston seal活塞密封
polytetrafluoroethene；PTFE聚四氟乙烯
poppet valve锥阀
portable particle counter便携式颗粒检测仪
port油口
Position feedback 位置反馈
power station液压泵站
pre-charge pressure充气压力
pressure control circuit压力控制回路
pressure drop；differential pressure压降
pressure gauge压力表
Pressure relief valve 压力溢流阀
pressure switch压力开关
pressure time diagram压力－时间图
pressure relief valve压力控制阀
pressure relief valve溢流阀
pressure recing valve减压阀
Progressive flow 渐增流量
Proportional valve 比例阀
proof pressure耐压试验压力
pulse generator脉冲发生器
quick release coupling快换接头
radial seal径向密封
rapid advance phase快进工步
rapid return phase快退工步
rated conditions额定工况
rated flow额定流量
rated pressure额定压力
rear end无杆端
Rectifier plate 节流板
recer fitting异径接头
replenishing line补液管路
reservoir fluid capacity油箱容量
resolution分辨率
retract stroke内缩行程
return line回油管路
repeat ability重复性
reprocibility复现性
rigid tube硬管
ripple波动
rod end有杆端
rod seal活塞杆密封
rotary seal旋转密封
Rotary knob 旋钮
rust protection防锈性
safety circuit安全回路
sandwich valve叠加阀
Sandwich plate valve 叠加阀
sealed reservoir闭式油箱
sensor传感器
sequence valve顺序阀
servo-valve伺服阀
shut-off valve截止阀
shuttle valve梭阀
silencer消声器
single-acting cylinder单作用缸
slide valve滑阀
solid contamination固体颗粒污染
Solenoid valve 电磁阀
speed regulator valve调速阀
static pressure静压力
sticking液压卡紧
steady-state conditions稳态工况
stiffness刚度
sub-plate底板
sub-plate valve板式阀
Sub-plate mount 板式安装
suction pressure吸入压力
supply flow供给流量
surge pressure冲击压力
system pressure系统压力
symbols for hydraulic and pneumatic components液压气动元件图形符号
symbols for fluid logic devices流体逻辑元件图形符号
symbols for logic functions逻辑功能图形符号
symmetry对称度
synchronizing circuit同步回路
telescopic cylinder伸缩缸
thermostat温度控制器
threshold阈值
Throttle valve 节流阀
transfer function传递函数
turbulent flow紊流
under lap负遮盖
unloading valve卸荷阀
valve阀
valve element阀芯
valve element position阀芯位置
variable displacement pump变量泵
valve pressure drop阀压降
valve polarity阀极性
viscosity粘度
water content含水量
welded fitting焊接式接头
wiper seal；scraper防尘圈密封
working cycle工作循环
working pressure工作压力
working phase工作工步
working stroke工作行程
working line工作管路
vane pump叶片泵
zero position零位
zero lap零遮盖

二、介质类
Emulsion 乳化液
Inhibitor缓蚀剂
Phosphate ester (HFD-R) 磷酸甘油酯
Synthetic lubricating oil 合成油
Water-glycol (HFC) 水-乙二醇
三、液压安装工程
Abrasion 摩擦
Argon 氩气
Butt welding 对接焊
Contamination 污染
Creep爬行
Dipping process 槽式酸洗
Extension （活塞杆）缩回
Failure 失效
Flushing 冲洗
Grout 灌浆
Inert gas welding 惰性气体焊
Jog 点动
Malfunction 误动作
Nitric acid 柠檬酸
Passivity 钝化
Pickling 酸洗
Retract（活塞杆）伸出
Re-circulation 循环
Socket welding 套管焊
四、管接头
Adjustable fittings/swivel nut 旋转接头
Banjo fittings 铰接式管接头
Bite type fittings 卡套式管接头
Bulkhead fittings 长直通管接头
Female connector fittings 接头螺母
Mal stud fittings 端直通管接头
Recers extenders 变径管接头
Tube to tube fittings 接管接头
union 直通接管接头
union elbow 直角管接头
union tee 三通管接头
union cross 四通管接头
Weld fittings 焊接式管接头
五、伺服阀及伺服系统性能参数
accessory 液压辅件
actuator 执行元件
cartridge valve 插装阀
circuit 液压回路
Coil impedance 线圈阻抗
common valve 普通阀
cylinder 液压缸
DDV-direct drive valve 直动式伺服阀
directional valve 方向控制阀
Dither 颤振电流
Dynamic response 动态频响
Flow saturation 流量饱和
flow valve 流量控制阀
Frequency response 频率响应
Hysterics 滞环
hydraulic system 液压系统
Lap 滞后
Linearity 线形度
motor 液压马达
NFPA-National Fluid Power Association 美国流体控制学会
Nozzle flapper valve 喷嘴挡板阀
Null 零位
Null bias 零偏
Null shift 零飘
pressure control 压力控制回路
pressure valve 压力控制阀
pump 液压泵
speed control 流量（速度）控制回路
directional valve control 方向控制回路
Phase lag 相位滞后
position control 定位回路
Pressure gain 压力增益
security control 安全回路
sequeunt circuit 顺序动作回路
Servo-jet pilot valve 射流管阀
Slope 曲线斜坡
superimposed valve叠加阀
Symmetry 对称性
synchronise circuit 同步回路
Threshold 灵敏度
valve 阀、

⑵ 机械类的英文 帮忙翻译一下 (不要自动翻译的)

The cantilever roadheader intelligent development direction
The cantilever tunneler is a complete cutting load coal rock and can be reproced themselves with spray out walking function such as st of roadway excavation joint unit cantilever part of underground tunnels in the coal face roadheader construction has been widely used in the development of social economy, with the progress of science and technology and improvement of living standard requirement to safe efficient roadway construction target direction to strengthen roadheader intellectualized development is a big trend of future mining machinery will fully equipped with automatic robot into an electronic integration of the electromechanical integration technology
This paper discusses the development of intelligence declared roadheader in the direction of the following four aspects of content of roadway excavation automatic forming roadheader section of intelligent control system of walking constant power control of inction adaptive system
End line control
Face shape control specific reflection to the cantilever roadheader machine is in operation on how the process control of roadheader cantilever cutting head movement driven to the provisions of section cutting shape
The movement is swinging cantilever bracket in vertical and horizontal planes in lifting movement in the synthesis of the rotary motion is a pair of cantilever swinging the synchrolifting lifting cylinder to complete a pair of the synchrolifting cylinder and the frame and cantilever were swinging hinged when lifting cylinder schele changes around the arms with frame will be restricted in the pivotal point as swing when lifting cylinder elongation to swing when the upper roadway cantilever when lifting cylinder to shorten the roadway when swinging and cantilever below can easily change JueJinTou in section of height
Roadheader cantilever level swing is turning on the rotary worktable level to realize the overall installed in horizontal part turn table when rotating table level swing in the installation of frame will drive the cantilever as level swing by a symmetrical layout rotary tables to promote the cylinder and the cylinder at level rotary worktable hinged on one side of the fuselage at work and the other side cylinder elongation of cylinder reced need to change the direction of the cantilever level swing only when the corresponding change a symmetric swinging cylinder piston rod movement direction by the hydraulic system and the level of lifting cylinder contact turning cylinders can separate motion can also do compound movement
JueJinTou center in section on the projection coordinate (x y) and cantilever lifting Angle and level Angle has one-to-one relationship and cantilever lifting Angle and angular is by lifting cylinder and the cylinder trip decided to turn the lift and rotary cylinder use can control the hydraulic cylinder cylinder travel itinerary JueJinTou can be controlled in the position and the roadway section cutting the provisions of section shape and size of roadway
Walk the intelligent control system
Excavation of the intelligent control system is walking to study how to walk or construction are always can keep the line movement has planned in fuselage sections on route in the process that won't because the machine and positioning itself to dig tunnels g and owed and ensure all sections of coal and rock can be on clean
Specific control process follows when fuselage centerline to excavate tunnels and design center JueJinTou front and center and coincidence point ring start-up curves on the rocker coincides JueJinTou began cutting motor rotate to make out a step length and mounted vertically and start rocker level rotary cylinder for automatic

⑶ 液压油缸的型号:UY-WE/M1-125/70*410 望解释一下液压油缸型号后的英文字母和数字各代表什么 谢谢 急

UY-WE/M1是液压缸的型号，各家生产的液压缸型号不同，代表的含义也不同，万变不离其宗。余下的都是通用的型号！125缸筒内径
70是活塞杆外径
410是有效行程！

⑷ 关于机电设备的专业英语词汇

Assembly line组装线

Layout布置图

Conveyer流水线物料板

Rivet table拉钉机

Rivet gun拉钉枪

Screw driver起子

Electric screw driver电动起子

Pneumatic screw driver气动起子

worktable 工作桌

OOBA开箱检查

fit together组装在一起

fasten锁紧(螺丝)

fixture 夹具(治具)

pallet栈板

barcode条码

barcode scanner条码扫描器

fuse together熔合

fuse machine热熔机

repair修理

operator作业员

QC品管

supervisor 课长

ME制造工程师

MT制造生技

cosmetic inspect外观检查

inner parts inspect内部检查

thumb screw大头螺丝

lbs. inch镑、英寸

EMI gasket导电条

front plate前板

rear plate后板

chassis 基座

bezel panel面板

power button电源按键

reset button重置键

Hi-pot test of SPS高源高压测试

Voltage switch of SPS 电源电压接拉键

sheet metal parts 冲件

plastic parts塑胶件

SOP制造作业程序

material check list物料检查表

work cell工作间

trolley台车

carton纸箱

sub-line支线

left fork叉车

personnel resource department

人力资源部

proction department生产部门

planning department企划部

QC Section品管科

stamping factory冲压厂

painting factory烤漆厂

molding factory成型厂

common equipment常用设备

uncoiler and straightener整平机

punching machine 冲床

robot机械手

hydraulic machine油压机

lathe车床

planer |'plein|刨床

miller铣床

grinder磨床

driller??床

linear cutting线切割

electrical sparkle电火花

welder电焊机

staker=reviting machine铆合机

position职务

president董事长

general manager总经理

special assistant manager特助

factory director厂长

department director部长

deputy manager | =vice manager副理

section supervisor课长

deputy section supervisor =vice section superisor副课长

group leader/supervisor组长

line supervisor线长

assistant manager助理

to move, to carry, to handle搬运

be put in storage入库

pack packing包装

to apply oil擦油

to file burr 锉毛刺

final inspection终检

to connect material接料

to reverse material 翻料

wet station沾湿台

Tiana天那水

cleaning cloth抹布

to load material上料

to unload material卸料

to return material/stock to退料

scraped |'skræpid|报废

scrape ..v.刮;削

deficient purchase来料不良

manufacture procere制程

deficient manufacturing procere制程不良

oxidation |' ksi'dein|氧化

scratch刮伤

dents压痕

defective upsiding down抽芽不良

defective to staking铆合不良

embedded lump镶块

feeding is not in place送料不到位

stamping-missing漏冲

proction capacity生产力

ecation and training教育与训练

proposal improvement提案改善

spare parts=buffer备件

forklift叉车

trailer=long vehicle拖板车

compound die合模

die locker锁模器

pressure plate=plate pinch压板

bolt螺栓

name of a department部门名称

administration/general affairs dept总务部

automatic screwdriver电动启子

thickness gauge厚薄规

gauge(or jig)治具

power wire电源线

buzzle蜂鸣器

defective proct label不良标签

identifying sheet list标示单

screwdriver holder起子插座

pedal踩踏板

stopper阻挡器

flow board流水板

hydraulic handjack油压板车

forklift叉车

pallet栈板

glove(s)手套

glove(s) with exposed fingers割手套

thumb大拇指

forefinger食指

midfinger中指

ring finger无名指

little finger小指

band-aid创可贴

iustrial alcohol工业酒精

alcohol container沾湿台

head of screwdriver起子头

sweeper扫把

mop拖把

vaccum cleaner吸尘器

rag 抹布

garbage container灰箕

garbage can垃圾箱

garbage bag垃圾袋

chain链条

jack升降机

proction line流水线

chain链条槽

magnetizer加磁器

lamp holder灯架

to mop the floor拖地

to clean the floor扫地

to clean a table擦桌子

air pipe 气管
packaging tool打包机

packaging打包

missing part漏件

wrong part错件

excessive defects过多的缺陷

critical defect极严重缺陷

major defect主要缺陷

minor defect次要缺陷

not up to standard不合规格

dimension/size is a little bigger尺寸偏大(小)

cosmetic defect外观不良

slipped screwhead/slippery screw head螺丝滑头

slipped screwhead/shippery screw thread滑手

speckle斑点

mildewed=moldy=mouldy发霉

rust生锈

deformation变形

burr(金属)flash(塑件)毛边

poor staking铆合不良

excesssive gap间隙过大

grease/oil stains油污

inclusion杂质

painting peel off脏污

shrinking/shrinkage缩水

mixed color杂色

scratch划伤

poor processing 制程不良

poor incoming part事件不良

fold of pakaging belt打包带折皱

painting make-up补漆

discoloration羿色

water spots水渍

polishing/surface processing表面处理

exposed metal/bare metal金属裸露

lack of painting烤漆不到位

safety安全

quality品质

delivery deadline交货期

cost成本

engineering工程

die repair模修

enterprise plan = enterprise expansion projects企划

qc品管

die worker模工

proction, to proce生产

equipment设备

to start a press开机

stop/switch off a press关机

classification整理

regulation整顿

cleanness清扫

conservation清洁
qualified procts, up-to-grade procts良品

defective procts, not up-to-grade procts不良品

waste废料

board看板

feeder送料机

sliding rack滑料架

defective proct box不良品箱

die change 换模

to fix a die装模

to take apart a die拆模

to repair a die修模

packing material包材

basket蝴蝶竺

plastic basket胶筐

isolating plate baffle plate; barricade隔板

carton box纸箱

to pull and stretch拉深

to put material in place, to cut material, to input落料

to impose lines压线

to compress, compressing压缩

character die字模

to feed, feeding送料

transportation运输

(be)qualfied, up to grade合格

not up to grade, not qualified不合格

material change, stock change材料变更

feature change 特性变更

evaluation评估

prepare for, make preparations for 准备

parameters参数

rotating speed, revolution转速

manufacture management制造管理

abnormal handling异常处理

proction unit生产单位

lots of proction生产批量

steel plate钢板

roll material卷料

manufacture procere制程

operation procere作业流程

to revise, modify修订

to switch over to, switch---to throw--over switching over切换

engineering, project difficulty

工程瓶颈

stage die工程模

automation自动化

to stake, staking, reviting铆合

add lubricating oil加润滑油

shut die架模

shut height of a die架模高度

analog-mode device类模器

die lifter举模器

argon welding氩焊

vocabulary for stamping

冲压常词汇

stamping, press冲压

punch press, dieing out press冲床

uncoiler & strainghtener整平机

feeder送料机

rack, shelf, stack料架

cylinder油缸

robot机械手

taker取料机

conveyer belt输送带

transmission rack输送架

top stop上死点

bottom stop下死点

one stroke一行程

inch寸动

to continue, cont.连动

to grip(material)吸料

location lump, locating piece, block stop 定位块

reset复位

smoothly顺利

dent压痕

scratch刮伤

deformation变形

filings铁削

to draw holes抽孔

inquiry, search for查寻

to stock, storage, in stock库存

receive领取

approval examine and verify审核

processing, to process加工

delivery, to deliver 交货

to return delivenry to.

to send delinery back

to retrn of goods退货

registration登记

registration card登记卡

to control管制

to put forward and hand in提报

safe stock安全库存

acceptance = receive验收

to notice通知

application form for purchase请购单

consume, consumption消耗

to fill in填写

abrasion磨损

reverse angle = chamfer倒角

character die字模

to collect, to gather收集

failure, trouble故障

statistics统计

demand and supply需求

career card履历卡

to take apart a die卸下模具

to load a die装上模具

to tight a bolt拧紧螺栓

to looser a bolt拧松螺栓

to move away a die plate移走模板

easily damaged parts易损件

standard parts标准件

breaking.(be)broken,(be)cracked 断裂

to lubricate润滑

common vocabulary for die engineering

⑸ 浴缸英语单词是什么

浴缸的英文单词有：

1、bathtub

英['bɑːθtʌb]美[bæθtʌb]

n. 浴缸，澡盆

双语例句：

Don'toverflowthebathtub.

别让浴盆里的水溢出来。

[其他] 复数：bathtubs

2、bath

英[bɑ:θ] 美[bæθ]

n. 沐浴；浴室；浴盆，浴缸

vt. 洗澡

vi. 洗澡

双语例句：

Hesluicedthebathandfilledit.

他冲洗了浴缸，然后放满了一缸水。

[其他] 第三人称单数：baths复数：baths现在分词：bathing过去式：bathed

3、tub

英[tʌb] 美[tʌb]

n. 浴盆，浴缸；桶

vt. 把…装入桶；为…洗盆浴

vi. 洗盆浴；（衣服等）被放在桶里洗

双语例句：

Thebathtubislargeenoughfortwopeople.

这个浴缸很大，足够两个人同时使用了。

[其他] 复数：tubs

4、whirlpools

英['hwə:lpu:l] 美['hwə:lpu:l]

n. 漩涡；浴缸；涡旋浴缸（whirlpool的复数）

双语例句：

Homespasorminiwhirlpoolsmassageandrelax,andcanbefittedintothebath.

家庭热水澡桶或是小型涡流浴缸能够按摩并放松身体，可以安装在浴室中。

[其他]原型：whirlpool

⑹ 油缸油缸用英语怎么说

油缸
[词典] hydro-cylinder;
[例句]并用该法对液压油缸的普通螺栓组紧联接进行回了优化设计答。
The method is employed for the optimal design for tight joints of ordinary bolt set on a hydraulic cylinder.

⑺ 油缸名词解释

变幅油缸

用来改变工作单元幅度的液压油缸称谓，例如：改变起重机吊臂的仰角，以满足各种工作幅度要求。变幅油缸多为双作用缸，工作时靠液压油压力伸出，靠重力回缩，因要求其伸出后有足够的刚度，故变幅油缸的活塞杆直径均较大。

摆动式液压缸

是输出扭矩并实现往复运动的执行元件，也称摆动式液压马达。有单叶片和双叶片两种形式。定子块固定在缸体上，而叶片和转子连接在一起。根据进油方向， 叶片将带动转子作往复摆动。

请参考油缸的分类: http://www.ycjzyy.com/news_detail.asp?id=188

⑻ 油压缸的英文单词是什么

oil cylinder 油缸; 油压缸

⑼ 往复旋转液压油缸英文怎么写

翻译结果
往复旋转液压油缸英文怎么写
Reciprocating rotating hydraulic cylinder how to write in English

⑽ 注塑机上的“油缸”和“油封圈”用英语怎么说

油缸 oil cylinder

油封圈 Oil seal

油缸漏油 cylinder leakage