压板英语怎么说及英文单词
Ⅰ 求电力专业英语翻译:母差保护,分列压板,开入异常三个单词的翻译。
电力英语不要完全相信翻译工具,会闹笑话,比如楼上某人。
母差保护:全称为母线差动保护,所以Bus differential protection是正确的
分列压板:分列不知道应该怎么叫,或许在合并单元的英文版资料中能找到“并列分列”的英文翻译。压板为连接端子触点一类,全称为connector,通常使用缩写conn。所以可能为SplitConn。
开入异常:开入是二进制信号Binary indication,所以开入在国外简称为BI,国内通常简称叫DI(Digital input),BI=DI,所以开入异常为BIAbnormal,或DIAbnormal。
Ⅱ 翻译成英语2
[ #89200911# ] one kind includes the hot bimetal piece, the control element and group of electrical electronic contacts warm controls the switch, its characteristic is: Its electrical electronic contact for often opens the condition, when its hot bimetal piece being heated elevates temperature to a definite value, its electronic contact becomes by the original separation condition puts through the condition, it is joined to acoustic, acousto-optic or the corresponding director, may use in each kind of heat source to include the electric heating, burns coal, heat source situation and so on under firewood, gas, oil, either to the pot which heats up is had to heater itself or in the pot the water temperature, food and so on carries on warm controls the newspaper news, the danger reports to the police or the safekeeping of security operation, the energy conservation operation. This warm controls the switch structure simply, cost low, the effect is good, facilitates practical. [ #89209324# ] safe energy conservation engine bed work flare, including Wan Xiangqiu 灯座 (1), clamp (2), Wan Xiangqiu (5), snake skin hose lampstand (6), electric wire (7) and (8), lamp holder (13), transformer B - [ 1 ], entire bridge rectifier D - [ 1 ] ~ D - [ 4 ], electric capacity C - [ 1 ] and three 基色 fluorescent lamps. Uses 9 tiles three 基色 fluorescent lamps to substitute for 60 tiles light bulbs to make the engine bed flare, achieved electricity saving 80%, the service life the engine bed work flare which uses compared to at present may enhance 6 times, also the light is gentle. This lamp uses 10 tiles power transformer, the reactive loss is small. 基色我不知道是什么。。。
Ⅲ 指压板的英文
指压板的英文是running man。撕名牌的英文是we are the champion。
Ⅳ 我的世界物品的翻译问题
Stone 石头
Dirt 泥土
Cobblestone 原石
Wood 木板
Sapling 树苗
Water 水
Lava 岩浆
Sand 沙子
Gravel 沙砾
Gold Ore 金矿
Iron Ore 铁矿
Log 木头
Red Log 红木
Birch Log 白杨木
Leaves 树叶
Sponge 海绵
Glass 玻璃
Lapis Lazuli Ore 青金石矿
Lapis Lazuli 青金石
Dispenser 发射器
Sandstone 沙石
Note Block 音符盒
White Wool 白羊毛
Orange Wool 橙羊毛
Magenta Wool 淡紫羊毛
Light Blue Wool 淡蓝羊毛
Yellow Wool 黄羊毛
Light Green Wool 浅绿羊毛
pink Wool 粉红羊毛
Gray Wool 灰羊毛
Light Gray Wool 浅灰羊毛
Cyan Wool
urple Wool 紫羊毛
Blue Wool 蓝羊毛
Brown Wool 棕羊毛
Dark Green Wool 墨绿羊毛
Red Wool 红羊毛
Black Wool 黑羊毛
Yellow Flower 黄花
Red Rose 红玫瑰
Brown Mushroom 棕蘑菇
Red Mushroom 红蘑菇
Gold Block 黄金块
Iron Block 铁块
Stone Slab 石板
Sandstone Slab 砂岩板
Wooden Slab 木制板
Cobblestone Slab 鹅卵石板
Brick 砖
TNT TNT
Bookcase 书架
Mossy Cobblestone 长满青苔
的鹅卵石
Obsidian 黑曜岩
Torch 火炬
Wooden Stairs 木楼梯
Chest 胸部
Diamond Block 钻石块
Workbench 工作台
Furnace 炉
Ladder 梯子
Minecart Tracks 矿车轨道
Cobblestone Stairs 鹅卵石楼
梯
Lever 杠杆
Stone Pressure Plate 石头压板
Wooden Pressure Plate 木制压板
Redstone Torch 红石火把
Stone Button 石头按钮
Ice 冰
Snow Block 雪块
Cactus 仙人掌
Jukebox 自动点唱机
Fence 栅栏
umpkin 南瓜子仁
Red Mossy Cobblestone 红色长满
青苔的鹅卵石
Slow Sand 慢砂
Lightstone Ore 浅石色矿
Jack-O-Lantern 杰克灯笼
Iron Spade 铁铲
Iron Pickaxe 铁锄
Iron Axe 铁斧
Flint and Steel 打火石
Red Apple 红苹果
Bow 弓
Arrow 箭头
Coal 煤炭
Diamond 钻石
Iron Ingot 铁锭
Gold Ingot 金元宝
Iron Sword 铁剑
Wooden Sword 木剑
Wooden Spade 木铲
Wooden Pickaxe 木柄鹤嘴锄
Wooden Axe 木斧
Stone Sword 石剑
Stone Spade 石锹
Stone Pickaxe 石镐
Stone Axe 石斧头
Diamond Sword 钻石剑
Diamond Spade 钻石锹
Diamond Pickaxe 钻石镐
Diamond Axe 钻石斧
Stick 棍子
Bowl 碗
Mushroom Soup 蘑菇汤
Gold Sword 金剑
Gold Spade 金锹
Gold Pickaxe 金镐
Gold Axe 金斧子
String 线
Feather 羽毛
Gunpowder 火药
Wooden Hoe 木锄
Stone Hoe 石锄
Iron Hoe 铁锄头
Diamond Hoe 钻石锄头
Gold Hoe 金锄头
Seeds 种子
Wheat 小麦
Bread 面包
Leather Helmet 皮革头盔
Leather Chestplate
Leather Pants 皮裤
Leather Boots 皮靴子
Iron Helmet 铁头盔
Iron Chestplate 铁护胸
Iron Pants 铁裤
Iron Boots 铁靴
Diamond Helmet 钻石头盔
Diamond Chestplate
Diamond Pants 钻石的裤子
Diamond Boots 钻石的靴子
Gold Helmet 金头盔
Gold Chestplate 金护胸
Gold Pants 黄金的裤子
Gold Boots 金靴子
Flint 燧石
ork 兽人
Grilled Pork 烤的猪肉
aintings 油画
Golden Apple 金苹果
Sign 标志
Wooden Door 木门
Bucket 桶
Water Bucket 水桶
Lava Bucket 岩浆桶
Mine Cart 矿山车
Saddle 马鞍
Iron Door 铁门
Redstone 红石
Snowball 雪球
Boat 小船
Leather 皮革
Milk Bucket 牛奶桶
Clay Brick 粘土砖
Clay Balls 粘土球
Reed 芦苇
aper 野猪
Book 本书
Slime Ball 泥球
Storage Minecart
owered Minecart 动力矿车
Egg 鸡蛋
Compass 指南针
Fishing Rod 钓鱼杆
Watch 手表
Lightstone Dust 星彩蓝宝石
Raw Fish 生鱼
Cooked Fish 煮熟的鱼
Ink Sac Dye 墨囊染料
Rose Red Dye 玫瑰红染料
Cactus Green Dye
Cocoa Beans Dye 可可豆染料
Lapis Lazuli Dye
urple Dye 紫色染料
Cyan Dye 青色染料
Light Gray Dye 淡灰色染料
Gray Dye 灰色染料
ink Dye 染料墨水
Lime Dye 石灰染料
Dandelion Yellow Dye
Light Blue Dye 淡蓝色染料
MagentaDye 品红色染料
Orange Dye 橙色染料
Bone Meal Dye 肉骨粉染料
Bone 骨
Sugar 糖
Cake 蛋糕
Gold Record 金唱片
Green RecordIf 绿色记录如果
Ⅳ 谁能告诉我英文单词"Cripter"是什么意思
简明英汉词典
griper [美俚]爱发牢骚的人
简明英汉词典
grippe
n.
流行性感冒
现代英汉综合大辞典
grippe
n.
[与定冠词连用]流行性感冒
简明英汉词典
gripper
钳子, 夹子
现代英汉综合大辞典
gripper
钳子, 夹子 两边有切刀的开沟梨 抓爪(器) 抓具 压板 (拉拨机小车的)牙板夹头 握住者
Ⅵ ML是什么意思
单词缩写
1. milliliter 毫升,计量单位。
进率:1L=1立方分米 = 0.001立方米
1ml=1立方厘米 = 0.000001立方米
ml 与 L 之间是1000进率,立方米,立方分米,立方厘米之间也是1000进率。
2. ml 英文 "make love" 的缩写,中文就是做爱的意思。常见于中国大陆网站,香港、台湾的网站也不多见。
在讲英文的国家,ml 并不代表做爱的意思。一般英文日常用语中, ml 仅代表 milliliter,毫升的意思。在英文字典中,并没有做爱这个解释。 一般人用 "have sex","sexual intercourse",或某个以F开头的俚语,等等。即使在网络上, 最简单的说法就是 sex。可以说,ml 这个缩写完全就是中式英语(英文:Chinglish),完全就是中国新新人创造发明的.
3.machine language 机器语言, makeup language 例如:
4.machine learning, 人工智能里面的机器学习
4.mali 非洲的马里共和国的国家代号缩写
5.millilambert 毫郎伯(亮度单位)
6.Merrill Lynch 投资银行
7.游戏《实况足球》中的大师级联赛:Master League 的简称也叫ML
8. ML语言: 通用的函数式编程语言。
9. ML准则: 统计检测与估值中的一种估计准则,即“”最大似然估计准则“。
[编辑本段]里氏
目前国际上使用的地震震级——里克特级数,是由美国地震学家里克特所制定,它的范围在 1 — 10 级之间。它直接同震源中心释放的能量(热能和动能)大小有关,震源放出的能量越大,震级就越大。里克特级数每增加一级,即表示所释放的热能量大了10倍。假定第1级地震所释放的能量为1,第2级应为10,第3级应为100,依此类推,第7级为100万,第8级则为1000万。
亦称近震规模(local magnitude,ML)、又译芮氏、黎克特制;里氏、黎克特制;里氏、芮氏震级,是表示地震规模大小的标度。它是由观测点处地震仪所记录到的地震波最大振幅的常用对数演算而来。由于地震仪的位置并不在震中,考虑到地震波在传播过程中的衰减以及其它干扰因素,计算时需减去观测点所在地规模0地震所应有的振幅之对数。黎克特制的单位是「级」。
做爱
makelove
ml《电子厂里有个部门是ml》
意思是压板
Ⅶ 关于机电设备的专业英语词汇
Assembly line组装线
Layout布置图
Conveyer流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪
Screw driver起子
Electric screw driver电动起子
Pneumatic screw driver气动起子
worktable 工作桌
OOBA开箱检查
fit together组装在一起
fasten锁紧(螺丝)
fixture 夹具(治具)
pallet栈板
barcode条码
barcode scanner条码扫描器
fuse together熔合
fuse machine热熔机
repair修理
operator作业员
QC品管
supervisor 课长
ME制造工程师
MT制造生技
cosmetic inspect外观检查
inner parts inspect内部检查
thumb screw大头螺丝
lbs. inch镑、英寸
EMI gasket导电条
front plate前板
rear plate后板
chassis 基座
bezel panel面板
power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试
Voltage switch of SPS 电源电压接拉键
sheet metal parts 冲件
plastic parts塑胶件
SOP制造作业程序
material check list物料检查表
work cell工作间
trolley台车
carton纸箱
sub-line支线
left fork叉车
personnel resource department
人力资源部
proction department生产部门
planning department企划部
QC Section品管科
stamping factory冲压厂
painting factory烤漆厂
molding factory成型厂
common equipment常用设备
uncoiler and straightener整平机
punching machine 冲床
robot机械手
hydraulic machine油压机
lathe车床
planer |'plein|刨床
miller铣床
grinder磨床
driller??床
linear cutting线切割
electrical sparkle电火花
welder电焊机
staker=reviting machine铆合机
position职务
president董事长
general manager总经理
special assistant manager特助
factory director厂长
department director部长
deputy manager | =vice manager副理
section supervisor课长
deputy section supervisor =vice section superisor副课长
group leader/supervisor组长
line supervisor线长
assistant manager助理
to move, to carry, to handle搬运
be put in storage入库
pack packing包装
to apply oil擦油
to file burr 锉毛刺
final inspection终检
to connect material接料
to reverse material 翻料
wet station沾湿台
Tiana天那水
cleaning cloth抹布
to load material上料
to unload material卸料
to return material/stock to退料
scraped |'skræpid|报废
scrape ..v.刮;削
deficient purchase来料不良
manufacture procere制程
deficient manufacturing procere制程不良
oxidation |' ksi'dein|氧化
scratch刮伤
dents压痕
defective upsiding down抽芽不良
defective to staking铆合不良
embedded lump镶块
feeding is not in place送料不到位
stamping-missing漏冲
proction capacity生产力
ecation and training教育与训练
proposal improvement提案改善
spare parts=buffer备件
forklift叉车
trailer=long vehicle拖板车
compound die合模
die locker锁模器
pressure plate=plate pinch压板
bolt螺栓
name of a department部门名称
administration/general affairs dept总务部
automatic screwdriver电动启子
thickness gauge厚薄规
gauge(or jig)治具
power wire电源线
buzzle蜂鸣器
defective proct label不良标签
identifying sheet list标示单
screwdriver holder起子插座
pedal踩踏板
stopper阻挡器
flow board流水板
hydraulic handjack油压板车
forklift叉车
pallet栈板
glove(s)手套
glove(s) with exposed fingers割手套
thumb大拇指
forefinger食指
midfinger中指
ring finger无名指
little finger小指
band-aid创可贴
iustrial alcohol工业酒精
alcohol container沾湿台
head of screwdriver起子头
sweeper扫把
mop拖把
vaccum cleaner吸尘器
rag 抹布
garbage container灰箕
garbage can垃圾箱
garbage bag垃圾袋
chain链条
jack升降机
proction line流水线
chain链条槽
magnetizer加磁器
lamp holder灯架
to mop the floor拖地
to clean the floor扫地
to clean a table擦桌子
air pipe 气管
packaging tool打包机
packaging打包
missing part漏件
wrong part错件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小)
cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头
slipped screwhead/shippery screw thread滑手
speckle斑点
mildewed=moldy=mouldy发霉
rust生锈
deformation变形
burr(金属)flash(塑件)毛边
poor staking铆合不良
excesssive gap间隙过大
grease/oil stains油污
inclusion杂质
painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色
scratch划伤
poor processing 制程不良
poor incoming part事件不良
fold of pakaging belt打包带折皱
painting make-up补漆
discoloration羿色
water spots水渍
polishing/surface processing表面处理
exposed metal/bare metal金属裸露
lack of painting烤漆不到位
safety安全
quality品质
delivery deadline交货期
cost成本
engineering工程
die repair模修
enterprise plan = enterprise expansion projects企划
qc品管
die worker模工
proction, to proce生产
equipment设备
to start a press开机
stop/switch off a press关机
classification整理
regulation整顿
cleanness清扫
conservation清洁
qualified procts, up-to-grade procts良品
defective procts, not up-to-grade procts不良品
waste废料
board看板
feeder送料机
sliding rack滑料架
defective proct box不良品箱
die change 换模
to fix a die装模
to take apart a die拆模
to repair a die修模
packing material包材
basket蝴蝶竺
plastic basket胶筐
isolating plate baffle plate; barricade隔板
carton box纸箱
to pull and stretch拉深
to put material in place, to cut material, to input落料
to impose lines压线
to compress, compressing压缩
character die字模
to feed, feeding送料
transportation运输
(be)qualfied, up to grade合格
not up to grade, not qualified不合格
material change, stock change材料变更
feature change 特性变更
evaluation评估
prepare for, make preparations for 准备
parameters参数
rotating speed, revolution转速
manufacture management制造管理
abnormal handling异常处理
proction unit生产单位
lots of proction生产批量
steel plate钢板
roll material卷料
manufacture procere制程
operation procere作业流程
to revise, modify修订
to switch over to, switch---to throw--over switching over切换
engineering, project difficulty
工程瓶颈
stage die工程模
automation自动化
to stake, staking, reviting铆合
add lubricating oil加润滑油
shut die架模
shut height of a die架模高度
analog-mode device类模器
die lifter举模器
argon welding氩焊
vocabulary for stamping
冲压常词汇
stamping, press冲压
punch press, dieing out press冲床
uncoiler & strainghtener整平机
feeder送料机
rack, shelf, stack料架
cylinder油缸
robot机械手
taker取料机
conveyer belt输送带
transmission rack输送架
top stop上死点
bottom stop下死点
one stroke一行程
inch寸动
to continue, cont.连动
to grip(material)吸料
location lump, locating piece, block stop 定位块
reset复位
smoothly顺利
dent压痕
scratch刮伤
deformation变形
filings铁削
to draw holes抽孔
inquiry, search for查寻
to stock, storage, in stock库存
receive领取
approval examine and verify审核
processing, to process加工
delivery, to deliver 交货
to return delivenry to.
to send delinery back
to retrn of goods退货
registration登记
registration card登记卡
to control管制
to put forward and hand in提报
safe stock安全库存
acceptance = receive验收
to notice通知
application form for purchase请购单
consume, consumption消耗
to fill in填写
abrasion磨损
reverse angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics统计
demand and supply需求
career card履历卡
to take apart a die卸下模具
to load a die装上模具
to tight a bolt拧紧螺栓
to looser a bolt拧松螺栓
to move away a die plate移走模板
easily damaged parts易损件
standard parts标准件
breaking.(be)broken,(be)cracked 断裂
to lubricate润滑
common vocabulary for die engineering
Ⅷ 人造板的常用英语有哪些
8035木业网的专家罗列了一下词语:
veneer 单板,薄板
debark 剥皮,卸载
scraper knife 刮刀
block 短圆木,木段
enclosure 机壳
rotary lathe 旋切机
chuck 卡头
spindle 卡轴,主轴
movable carriage 移动式刀架
clipper 剪扳机
veneer dryer 单板干燥机
damper 风挡,气闸
venting stack 排气管
edge gluing process 侧面胶拼工艺
splicing 胶拼,拼接
stringing 串接,捆接
stitching 压合,滚压,缝合
patch hole 嵌补孔
panel patching 板的嵌补
scarfing 斜接,嵌接
roller spreader 滚筒涂前胶机
sprayline 喷涂生产线
curtain coater 淋涂机
workmanship 工艺,技巧
hydraulic ram 液压柱塞
opening 开口,开档
assembly 配板,组坯
plywood 胶合板
particleboard 刨花板
cement-bonded board 水泥刨花板
mineralbonded board 矿质胶合刨花板
dry-process 干法(工艺)
fiberboard 纤维板
lignocellulosic 木素纤维素的
hardboard 硬质纤维板
insulation board 绝缘板
molded proct 模压产品
dimensional stability 尺寸稳定性
reliability 可靠性,安全性
composition-board 复合板
classifier 分选器
press loader 压机装料机
press unloader 压机卸料机
alignment 定向,排列成行
slurry 浆,淤浆
platen-pressed system 压板系统
extruded system 挤压系统
planer shaving 刨花
flake 刨花,刨片
wafer 大片刨花,薄片
furnish 碎料
tempered hardboard 热处理硬质纤维板
insulation board 绝缘板
lignin bond 木素胶合
wet-process 湿法(工艺)
dry- process 干法(工艺)
defiberizing 纤维分离
semidry mat 半干板坯
press cycle 热压周期
pyrolytic breakdown 热解破坏
Ⅸ 求机械专业术语的解释及英文翻译
1)电化学腐蚀 electrochemical corrosion
电化学腐蚀就是金属和电解质组成两个电极,组成腐蚀原电池。
2)车架 automotive chassis
车架是跨接在汽车前后车桥上的框架式结构,俗称大梁,是汽车的基体。
3)悬架 suspension
悬架是汽车的车架(或承载式车身)与车桥(或车轮)之间的一切传力连接装置的总称,其作用是传递作用在车轮和车架之间的力和力扭,并且缓冲由不平路面传给车架或车身的冲击力,并减少由此引起的震动,以保证汽车能平顺地行驶。
4) 转向器 redirector
转向器的作用是把来自转向盘的转向力矩和转向角进行适当的变换(主要是减速增矩),再输出给转向拉杆机构,从而使汽车转向,所以转向器本质上就是减速传动装置。
5)变速器 speed changer
变速器是用来改变来自发动机的转速和转矩的机构,它能固定或分档改变输出轴和输入轴传动比,又称变速箱。
6)板料冲压 sheet metal parts
板料冲压是利用冲模,使板料产生分离或变形的加工方法。因多数情况下板料无须加热,故称冷冲压,又简称冷冲或冲压。
7)孔加工 spot facing machining
孔加工一般分为钻孔,铰孔,扩孔,镗孔,拉孔。 机床上对孔的加工可以用钻头、镗刀、扩孔钻头、铰刀、拉刀进行钻孔、镗孔、扩孔、铰孔和拉孔。
8) 刚度 rigidity
刚度是指材料或结构在受力时抵抗弹性变形的能力。是材料或结构弹性变形难易程度的表征。
9)标准件 standard component
标准件是指结构、尺寸、画法、标记等各个方面已经完全标准化,并由专业厂生产的常用的零(部)件,如螺纹件、键、销、滚动轴承等等。
10) 脆性材料 brittleness material
在外力作用下(如拉伸、 冲击等)仅产生很小的变形即破坏断裂的材料。脆性材料在外力作用下(如拉伸、 冲击等)仅产生很小的变形即破坏断裂的性质。
11)垫圈 washer
指垫在被连接件与螺母之间的零件。一般为扁平形的金属环,用来保护被连接件的表面不受螺母擦伤,分散螺母对被连接件的压力。
12) 塑性变形 plastic distortion
塑性变形是物质-包括流体及固体在一定的条件下,在外力的作用下产生形变,当施加的外力撤除或消失后该物体不能恢复原状的一种物理现象。