空載變速英語怎麼說及英文翻譯
Ⅰ 翻譯成英文
1、懸掛點焊機 Suspension Spot Welding Machine
2、型號Model
3、電源電壓Power Supply
4、額定容量Rated Capacity
5、額定負載持續率Rated Duty Cycle
6、最大焊接功率Maximum Welding Power
7、次級空載電壓Secondary Unload Voltage
8、絕緣等級nsulation Level
9、冷卻水流量Cooling Water Flow Rate or Chilled-water Flow Rate
Ⅱ 變壓器專業英語翻譯，跪求各位英語達人翻譯。
Roll the sealed type distribution transformer core is developed in recent years, the new generation of low noise, low loss, and its core transformer no juncture, rece no-load loss and no-load current no-load current, high ~ 80%, 60% lower in iron wire wound on continuous windings, tight, concentricity well. Noise dropped 10 decibels. Due to the continuous winding, iron makes full use of the manufacturing of sexual orientation, no-load loss reced by 20% ~ 30%, is a new generation of high-tech energy-saving and environmental protection procts.
The sealed type distribution transformer USES don't hang core structure, make internal and external tank completely isolated, no storage cabinets, the thermal changes in transformer tank operation by elastic corrugated chips to make compensation for expansion, transformer oil and insulation parts with outside air, water, and the separation of transformer oil and slow the aging in insulation parts. Seal of high fuel oil resistant balata, but not in the circumstance that hang core inspection operation for 20 years, rece operation maintenance cost, be helpful for the inconvenience. Some maintenance
The new type S9 oil-immersed three-phases transformer USES unified design standards, advanced and reasonable structure, insulation resistance short-circuit capacity is strong, its performance achieved the international similar proct level, with S7 procts, on average, no-load loss dropped by 10.25% no-load current decline 37.7%, load loss and lower average 22.4% appearance, reasonable structure according to user's chip and tank can tubular radiator, in recent years is one of the most widely used energy saving procts.
Developed SC9 series of epoxy resin casting dry-type power transformer and air insulated SG type dry type transformer insulation resistance short-circuit capacity, good performance, high impact resistance level of lightning. Epoxy resin casting dry-type distribution transformer winding high by epoxy resin casting seal, adoption of epoxy resin performance is good, crack, high temperature resistant, high mechanical strength, long service life. Flame retardant, moistureproof, explosion-proof pollution-free.
Procts, small volume, low noise. The winding in the operation of automatic temperature monitoring and are protected alarm device. In the forced air cooling can make the rated capacity over 40%. Can be widely used in high-rise buildings, station, wharf, subway, airport, power transmission and distribution system is the important place.
Combined-type distribution transformer (American box variable) is a new body, transformer switch, fuse, tap-changer and relevant auxiliary equipment in one of the transformer. With all its insulation, seal structure, and adopt double welding wire protection. Transformer core adopts special structure, low consumption, low noise, no heat, lightning case. High-pressure line adopts elbow joint, can operate cable 200A load current, can be done in an emergency operation, load switch with isolation switch features. Combined transformer, compact structure, small volume, cover an area of an area small, less investment, easy to install and can be widely used in airport, high-rise buildings, business center, dweller, streets, can further load center installation. When ordering, please indicate the combined transformer or terminal type ring network.
SZ type power transformer on-load changer, in use process for saving transformer on-load changer with reliable quality, reasonable, accord with national economic indicators GB1094-1996 power transformer and GB/T6451-1999 "three-phase oil-immersed transformer, electric technical parameters and requirements. Core adopts the high quality manufacturing, advanced proction technology, Oil and winding road structural design is reasonable, high mechanical strength and resistance short-circuit capacity is strong, beautiful generous.
僅作參考
Ⅲ 請幫我翻譯，專業英語
在環境溫度下，應能於30s內起動成功。
should be able to start up successfully within 30 seconds at ambient temperature.
在允許的工作環境溫度運行停機後，應能於30s內重新起動成功。
should be able to re-start successfully within 30 seconds when stopped at operating ambient temperature.
送檢樣機經檢驗, 健康與安全基本要求除標志（無製造年份），其餘項目與歐盟 98/37-EC機械指令一致。
The submitted prototype has been inspected , the health and safety, and other items apart from the mark (no manufacturing time) conform to the basic requirements of EU Machinery Directive 98/37-EC.
燃油消耗率 specific fuel consumption，
常溫起動 cold starting，
熱起動 hot starting，
穩定調速率 steady state speed governing rate，
最大扭矩及轉速 maximum torque and speed，
最低空載穩定轉速 minimum no-load steady speed，
最低空載穩定轉速波動率 fluctuation ratio of minimum no-load steady speed.
Ⅳ 哪位達人大哥,幫小妹翻譯一下這些專業名詞吧,我在這里向各位達人致敬了!!
樓上從網上拷貝那麼多有什麼用？誤人啊！
還不如實實在在地幫人翻譯一下：
（本人在外企車間干過，這些工具的英文名是常用的）
電動工具槍Electric Tool Gun,螺絲頭Screw Head,螺絲刀Screw Driver,台鉗Bench Clamp,半圓挫Half Round File,半圓鏟Half Round Scraper,大力鉗Heavy Tong,螺母Nut,外鈑手Outside Spanner,內鈑手Inside Spanner,喉鉗Throat Tong,拉尺Tape Measure,鉗子Pliers,螺絲刀Screw Driver,電鑽Electric Drill,沖擊鑽Hammer Drill,扳手Wrench,尖嘴鉗子Nose Pliers,夾板Splint,蟹叉Crab Fork,內六角扳手Allen Wrench,喉夾Throat Clamp,圓挫刀 Round File,扁形挫刀Flat File,長角鐵Long Angle Iron,中角鐵 Middle Angle Iron,小角鐵Small Angle Iron,緊固片Fitting Fastening
Ⅳ 維修工具的英語翻譯
一畫
一字螺絲批 slot type screwdriver
一點透視 one-point perspective
二畫
二合一黏合劑 epoxy resin adhesive
二合膠；混合膠 epoxy glue
二維的；平面的 two-dimensional
二進制 binary
二極體；整流子 diode
二號螺絲攻 second tap
二路開關 two-way switch
十進制的；公制的 metric
人工製品 artefact
人造板 man-made board
人體工程學 ergonomics; human engineering
人體尺寸 human dimension
人體測量學 anthropometry; anthropometrics
刀片 blade
刀身 blade
刀具 tool
刀具溜座 carriage
刀柱 tool post
刀架 tool rest
刀架底座 tool rest bracket
刀座帷；床鞍 apron
刀座鞍；溜板座 saddle
力 force
力三角形 triangle of force
力平行四邊形 parallelogram of force
力多邊形；多邊形力學 polygon of force
力的分解 force resolution
力架；亮漆 lacquer
力矩 moment
力偶 couple
力矩定律 law of moment
力-距離圖表 force-distance graph
力圖 force diagram
力線 line of force
力點 effort
十字榫 cross halving joint
十字螺絲 Philip's head screw
十字螺絲批 Philip's type screwdriver
丁字尺；T 尺 tee square
三畫
三爪夾頭 three-jaw chuck
三角尺 set square
三角形結構系桿 triangulation tie
三角銼 triangular file
三維的；立體的 three-dimensional
三氯甲烷；哥羅芳 chloroform
三聚氰胺；蜜胺 melamine
三點透視 three-point perspective
上油漆 painting
上釉 enamelling
凡立水 varnish
叉形頂尖 fork centre
口罩 mask
士力；蟲漆 shellac
士巴拿；扳手 spanner
大芯夾板；寬條芯夾板 blockboard; solid corestock-laminated board
大量製造 mass proction
子口刨；槽口刨；邊刨 rebate plane
小型平槽刨 miniature router plane
小型線料彎曲器 small wire bender
小型彎折機 mini bender
小型電路斷路器；跳菲 miniature circuit breaker (MCB)
小齒輪 pinion
山樟 San Cheong
工件 workpiece
工字梁 I beam
工作面 working surface
工作圖；製作圖 working drawing
工作台 bench; working table
工具 tool
工具貯存室 tool storage
工具槽 well
工具鋼 tool steel
工場 workshop
工場安全 workshop safety
工程字書寫技巧 lettering
工程系統 engineering system
工程繪圖 engineering drawing
工業酒精；火酒 methylated spirit
弓形手鑽；手搖曲柄鑽 brace
弓形手鑽嘴 brace bit
弓鋸 bow saw; hacksaw
弓鋸片 hacksaw blade
弓鋸床 hacksawing machine
四畫
不平衡 imbalance
不含鐵金屬；非鐵金屬 non-ferrous metal
不貫穿孔；閉孔；盲孔 blind hole
不貫穿鳩尾榫 lapped dovetail joint
不對稱 asymmetry
不銹鋼 stainless steel
不穩定平衡 unstable equilibrium
中心 centre
中心線 centre line
中心沖 centre punch
中心鑽 centre drill
中心鑽嘴 centre bit
中央處理器 central processing unit (CPU)
中性 neutral
中性平衡；隨遇平衡 neutral equilibrium
中性軸 neutral axis
中密度纖維板 medium density fibre board (MDF)
中粗銼紋 second cut
中碳鋼 medium carbon steel
中線 neutral wire
互補金屬氧化物半導體 complementary metal oxide semiconctors (CMOS)
介子；墊片 washer
介指鐵 ring mandrel
介電常數；電容率 permittivity
介穩態的；亞穩態的 metastable
內力 internal force
內卡尺 inside calipers
內能 internal energy
內涵性質 intensive properties
內圓彎鑿 scribing gouge
內鎖式配件 interlocking fitting
內燃機 internal combustion engine
內螺紋製造法 tapping
內螺絲 internal thread
內彎邊 concave edge
六角金屬枝 hexagonal bar
六角匙 Allen key
六角頭螺絲 hexagonal head screw
公制的；十進制的 metric
公差 tolerance
冗餘構件 rendant member
分力 component force
分子 molecule
分子力 molecular force
分切；分割；切斷 parting off
分貝 decibel
分析 analysis
分析及批判學 analytical and critical studies
分析器 analyzer
分流器 shunt
分界面；界面；介面 interface
分厘卡 micrometer
分規 divider
分割車刀架 parting tool holder
分解 decomposition
分壓器 potential divider; voltage divider
隔離開關 isolating switch
切削工具 cutting tool
切削液 cutting fluid
切削深度 depth of cut
切屑；碎屑 chip
切線鋸法 tangential sawing
切輥紋；滾紋 knurling
切斷；分切；分割 parting off
切斷工具 parting tool
勾；勾腳 hook
勾刀；膠片刀 plastic cutter
化膠水 tensol
反向偏壓 reverse biased
反相放大器 inverting amplifier
反相器 inverter
反射 reflection
反電動勢 back e.m.f.
反饋；回輸 feedback
天拿水；稀釋劑 thinner
天梯牙；齒條 gear rack
天然木材 natural timber
天然乾燥法 air seasoning
孔隙率 porosity
尺寸 dimension
尺寸線 dimension line
尺身 blade
引力；重力 gravitational force
心形凸輪 heart-shaped cam
心材 heartwood
心軸 mandrel
心銷 core pin
手工具 hand tool
手工鋸 junior hacksaw
手削法 paring
手持虎鉗 hand vice
手柄 handle
手套 gloves
手掃漆 brushing lacquer
手推車 barrow
手提式豎線鋸 portable jigsaw
手提電動工具 portable power tool
手提電鑽 electric hand drill
手進給 hand feed
手搖曲柄鑽；弓形手鑽 brace
手搖鑽 hand drill
手銼 hand file
手鋸；板鋸 handsaw
手錐 bradawl
手轆軋機 hand rolling machine
支柱；支撐物 strut
支架；支座 support
支點 fulcrum; pivot
文字 text
方向 direction
方向針 pointing needle
方枝 square bar
方波形 square waveform
方波產生器 squarer
方型牙板 rectangular die
方格紙；網格紙 grid paper
方通 square tube
方塊圖 block diagram
方銼 square file
方頭鑽嘴 square shank bit
方螺帽 square nut
方邊鑿；直邊鑿 firmer chisel
木 wood
木工 woodwork
木工工作間 woodwork area
木工工作台 woodworker's bench
木工車床 wood turning lathe; woodworking lathe
木工鉛筆 carpenter's pencil
木工刨床 thicknessing and planning machine
木牙螺絲；木螺釘 wood screw
木材 timber
木材車削 wood turning
木材車削工具 wood turning tools
木屑壓合板；萬花板 chipboard
木條接榫 corner strip joint
木圓頭槌 doming mallet
木模；模型 patterns
木線 wood strip
木膠粉 ureaformal dehyde resin glue
木銼 rasp
木螺釘；木牙螺絲 wood screw
木槌 mallet
止推軸承 thrust bearing
止推墊圈 thrust washer
比例 proportion
比例尺 scale
比例常數 proportionality constant
比例極限 proportional limit
比較器 comparator
比熱容量 specific heat capacity
水平投影面 horizontal plane
水平儀；平水尺 spirit level
水氣掣；漏電斷路掣 earth leakage circuit breaker (ELCB)
水晶膠；聚酯樹脂 polyester resin
水晶膠的鑄造成形 resin casting
水磨砂紙 silicon carbide paper
火叉 firing fork
火水；煤油 kerosene
火牛；變壓器 transformer
火石輪 grinder
火花電蝕法；放電極加工 electrical discharge machining
火酒；工業酒精 methylated spirit
火鉗 tongs
火線；活線 live wire
火磚 fire brick
爪扣；爪形離合器；犬齒式離合器 dog clutch
牙板；絲模 die
牙板扳手；絲模扳手 die holder (stock)
牙板螺帽 die nuts
牛皮膠；動物膠 animal glue
牛油紙 tracing paper
牛頓運動定律 Newton's laws of motion
犬齒式離合器；爪扣；爪形離合器 dog clutch
五畫
丙烯;丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS)
主軸；心軸 spindle
主題 motif
令(紙張的計數單位) ream
凹座 recess
凹模 hollowing block
凸緣 flange
凸緣聯軸節 flange coupling
凸輪 cam
凸輪式配件 cam-action fitting
凸輪傳動 cam drive
凸頭螺絲 raised head screw
加成作業；添加法 addition process
加油 oiling
加速器 accelerator
功能；用途 function
功率因子 power factor
功率放大器 power amplifier
功率板 power amplifier board
功率晶體管 power transistor
包氏記號法 Bow's notation
「包浩思」；「包豪斯」〈設計風格) Bauhaus
半永固法；半永久接合 semi-permanent joining
半接榫 halving joint
半閉式槽榫 stopped housing joint
半圓(木)銼 half-round rasp
半圓車刀 turning gouge
半圓銼 half-round file
半圓頭鉚釘 snap rivet
半導體 semiconctor
卡路里；卡(熱量單位) calorie
卡紙 card paper
卡尺；測徑器 calipers
去角；倒角 chamfer
可切削性 machinability
可行性 feasibility
可逆過程 reversible process
可壓縮性 compressibility
可變電阻 variable resistor
四分儀 quadrant
四爪夾頭 four-jaw independent chuck
四圓心法(繪圖) four-centre method
外卡尺 outside calipers
外形塑造 shaping
外形線；輪廓線 outline
外推法 extrapolation
外圓彎鑿 firmer gouge
外螺紋 external thread
外螺紋製造法 threading
外彎邊 convex edge
外觀 appearance
失真 distortion
尼龍；聚醯胺 nylon; polyamide (PA)
尼龍墨水針筆 technical felt-tip pen
左右調校桿 lateral adjusting level
市售尺寸；標准尺寸 stock size
市電頻率；電源頻率 mains frequency
平(木)銼 flat rasp
平水尺；水平儀 spirit level
平行投影 parallel projection
平行車削 parallel turning
平行虎鉗 parallel vice
平行釘法 parallel nailing
平底彎刨 flat faced spokeshave
平底鑽嘴 forstner bit
平板結構 slab construction
平流扼流圈；濾波扼流器 smoothing choke
平流電容器；濾波電容器 smoothing capacitor
平流電路；濾汳電路 smoothing circuit
平面板；正台 surface plate
平面圖；俯視圖 plan
平面錘 flatter
平移 translation
平搭榫 corner halving joint
平嘴鉗 flat nose pliers
平槽刨 router plane
平衡 balance; equilibrium
平衡力 equilibrant
平衡條件 equilibrium condition
平衡電橋 balanced bridge
平頭弧刀 square nose gouge
幼紋 smooth cut
打凹成形 hollowing
打凸成形 raising
打槽機 routing machine
打線；打槽 routing
打磨 fitting; polishing
打磨機 polisher
本生燈 Bunsen burner
本徵半導體 intrinsic semiconctor
正反器；觸發器；復振器 flip-flop
正反饋；正回輸 positive feedback
正火 normalizing
正向偏置 forward bias
正投影 orthographic projection
正投影圖 orthographic drawing
正弦波形 sinusoidal waveform
正面投影 front projection
正視圖 elevation; front elevation
正極；陽極 anode
正齒輪 spur gear
正台；平面板 surface plate
永久性接合 permanent joining
瓦通紙；瓦楞紙板 corrugated board
生長層 cambium layer
生產圖 proction drawing
生膠漿 rubber cement
生鋼；鑄鋼 cast steel
生鐵；鑄鐵 cast iron
用途；功能 function
白楊木 poplar
白膠漿 PVA glue; white glue
皮沙墊 leather sandbag
皮革 leather
皮革黏合劑 leather glue
皮鞋 leather shoes
目錄 contents
矢量；向量 vector
石灰岩 limestone
石英晶體振盪器 quartz crystal oscillator
石棉 asbestos; asbestus
石膏 Plaster of Paris
示波器 oscilloscope
立體圖 pictorial drawing
六畫
交流電流 alternating current (a.c.)
交流電壓 a.c. voltage
交聯結構 cross-linked structure
仿飾金 gilding metal
伏特 volt
光力架 clear lacquer
光拉軟鋼 bright drawn mild steel (B.D.M.S.)
光敏電阻 light dependent resistor (LDR)
光測彈性學 photoelasticity
光刨；滑刨 smoothing plane
光電效應 photoelectric effect
光澤 lustre
全閉式槽榫 closed housing joint
共面力 coplanar force
共聚合作用 co-polymerization
共聚物 copolymer
共價鍵 covalent bond
共振；共鳴；諧振 resonance
印刷電路板 printed circuit board (PCB)
同素異形 allotropy
同軸電纜 coaxial cable
同溫 equality of temperature
向量；矢量 vector
向量和 vector sum
合力 resultant force
合口扁鉗 close mouth tongs
合成色；等和色 secondary colour
合成品 composite
合成粅料 composite material
合金 alloy
合金工具鋼 alloy tool steel
合釘；定位銷 dowel
回火 tempering
回復力 restoring force
回復力偶 restoring couple
回彈 resilience
回輸；反饋 feedback
地線 earth wire
多刃切削刀具 multi-point cutter
多孔塑料；泡沫塑料；海綿狀塑料 foam plastics
多方榫接合 pinned joint
多媒體 multi-media
多晶性 polycrystallinity
多諧振動器；多諧振盪器 multivibrator
多邊形力學；力多邊形 polygon of force
字母沖 letter punch
字板 letter stencil
安全 safety
安全守則 safety rule
安全系數 safety factor
安全措施 safety precaution
安全眼罩 safety goggle
安全設備 safety equipment
安全葯箱 safety box
安培 ampere
安培計；電流表 ammeter
尖腳 spur
年輪 annual ring
成本 cost
成形 forming
扣件；擊固件 fastener
扣釘 clout nail; cramp
托架 bracket
收縮 shrinkage
曲柄 crank
曲柄軸 crank shaft
曲線規；雲板；雲尺 French curve
有效的 efficient
有效電流 effective current
灰；灰末 ash
百折膠；百折膠；聚丙烯 polypropylene (PP)
竹 bamboo
羊角錘 claw hammer
老化 ageing
肋條 rib
肌理；質感；質地 texture
自由度 degree of freedom
自動控制 automatic control
自動進給 auto-feed
自然乾燥法 natural seasoning
自感量 self-inctance
自感應 self-inction
色彩；顏色 colour
色調 tone
色環 colour wheel
行星齒輪；周轉齒輪 epicyclic gear
七畫
肘節開關 toggle-switch
串激電動機；串繞電動機 series-wound motor
位能；勢能 potential energy
位梯度；勢梯度 potential gradient
位移 displacement
位錯 dislocation
伸長度 elongation
作工硬化 work hardening
作功 work done
作圖線 construction line
低密聚乙烯 low density polyethylene (LDPE)
低通濾波器 low-pass filter
低電壓 low voltage
低碳鋼 low carbon steel
布置 layout
免油軸承 oil-less bearing
冷加工；冷作工 cold working
冷加工硬化 cold work hardening
冷色 cool colour
冷軋壓 cold rolling
冷卻系統 cooling system
冷卻效應 cooling effect
冷卻液流量 coolant rate
冷凝膠；環氧樹脂 epoxy resin
利口；「披」口；鐵屑 burr
刨平 planing
刨花板；碎料板 particle board
吹風機 air blower
吹氣模塑；吹模塑 blow moulding
吹管 blow pipe
含鐵金屬 ferrous metal
含水量 moisture content
坑鑿 cross-cut chisel
均方根值 root mean square value
均角投影圖；等角投影圖 isometric drawing
均速圓周運動 uniform circular motion
夾；夾鉗 clamp
夾 cramp
夾卡 mounting board
夾具 fixture; jig
夾具及固定裝置 jig and fixture
夾板；膠合板 plywood
夾持工具 clamping device; holding tool
夾背鋸；榫鋸 tenon saw
夾頭 chuck
夾頭開啟匙；夾頭扳手 chuck key
夾迭黏合成形 lamination
尾座 tailstock
床身；床道 lathe bed
床鞍；刀座帷 apron
形心；面心 centroid
形狀 shape
形變 deformation
「快把」板；硬質纖維板 hardboard
快速移位 rapid traverse
抗扭強度 torsional strength
抗屈強度 bending strength; yield strength
抗性分量；無功分量 reactive component
抗拉強度 tensile strength
抗氧化劑 anti-oxidant
抗剪強度 shearing strength
抗磁性物料 diamagnetic material
抗撓性 stiffness
抗壓強度 compressive strength
抗斷強度 breaking strength
技術員；技師 technician
扶架 steady
扭力 torsion
扭矩；轉矩 torque
扭轉 torsion
扭轉角 angle of torsion
把手 hand grip
扼流圈 choke
扳手 spanner; wrench
投影 projection
投影面 projection plane
投影線 projection line
攻絲 tap
材料 material
材料單；材料表 material list
杜拉鋁 ralumin
杉木 spruce
步進電動機 stepper motor
步沖輪廓法 nibbling
每分鍾轉數 revolution per minute (r.p.m.)
系統組件 system component
角托架 angle bracket
角位移 angular displacement
角板；直角板 angle plate
角度 angle
角榫 corner angle joint; corner joint
角鐵 angle iron
谷巴凡立水 cobal varnish
車刀架 tool holder
車床 lathe
車床工具 lathe tools
車床中心鑽咀 lathe centre bit
車床操作法 lathe operation
車削；車旋 lathe turning; turning
車削工具 turning tools
防火膠板 Formica
防銹 rust prevention
防聲耳筒；護耳器 ear-protector
防松螺帽 lock nut
防護裝置；保護罩；保護網 guard; safety guard
八畫
注射成形法；噴射鑄造法 injection moulding
並激電動機；並繞電動機 shunt-wound motor
乳酪膠 casein glue
乳膠漆 emulsion paint
亞加力；壓克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA)
亞穩態的；介穩態的 metastable
來回擺動 oscillating
兩點透視 two-point perspective
刻度；劃線 ruling
刺沖 dot punch
刮刀 scraper
刮擦 scraping
制動鼓 drum brake
制動碟 disc brake
制動器 brake
受迫振動 forced vibration
受迫振盪 forced oscillation
和諧 harmony
周轉齒輪；行星齒輪 epicyclic gear
固定夾；台夾 bench holdfast
固定負載 dead load
定子 stator
定位銷；合釘 dowel
定位螺絲 set screw
定距輪 stitch marker
屈片機 folding machine
屈曲 bending
屈服點；降服點 yield point
屈圈法 loop forming
屈卷法 scrolling
屈接縫 folded lap seam
屈喉機 tube bender
屈折 folding
屈折線 folding line
屈壓接縫 folded & grooved seam
延性 ctility
延性的 ctile
弦鋸法 plain sawing
弧口鑿；圓鑿 gouge
往復式運動 reciprocatory motion
拉力 tensile force
拉力計；張力計 tensiometer; tensometer
拉釘 blind rivet; pop rivet
拉釘接合 blind riveting; pop riveting
拉釘鉗 blind riveting pliers; pop riveting pliers
拉張 tension
拉張應力 tensile stress
拉張應變 tensile strain
拉細 drawing-down
拉製法 drawing
拉線 wire drawing
「披」口；利口；鐵屑 burr
拔鉗 nippers
拋光 buffing
拋光機 buffing machine
放大；擴大 enlargement
放大尺 pantograph
放大倍數 amplification factor
放大器 amplifier
放電極加工；火花電蝕法 electrical discharge machining
易用萬能尺 line setter
易碎 fragile
〈繪畫的〉明暗運用；描影 shading
枝；桿 rod
杯形頂尖 cup centre
杯頭螺絲 hexagonal socket head cap screw
板鋸 panel saw
松木 pine
松節水 turpentine
法式磨光 French polishing
法拉〈電容量單位〉 farad
油石；磨刀石 oil stone
油漆；塗料 paint
泡沫塑料；多孔塑料；海綿狀塑料 foam plastics
物理特性 physical property
物理屬性 physical attribute
物理量 physical quantity
盲孔；閉孔；不貫穿孔 blind hole
直尺 ruler; straight rule
直角叉榫 corner bridle joint
直角尺 try square
直角板；角板 angle plate
直角杠桿 bell crank lever
直身鑽嘴 straight shank drill
直車刀架 straight tool holder
直流發電機 d.c. generator
直流電流 direct current (d.c.)
直流電動機；直流馬達 d.c. motor
直紋鋸 rip saw
直線切削 linear interpolation
直線運動 rectilinear motion
直邊鑿；方邊鑿 firmer chisel
直鐵剪 straight snips
硅 silicon
空行程 idle stroke
空氣動力學 aerodynamics
空間 space
空載 no load
花紋鑿 embossing stamp
花梨木 rosewood
花樣；圖案 pattern
虎克定律 Hooke's Law
虎鉗 vice
虎鉗護罩 vice clamp
初步意念 proposed solution
表面 surface
表面展開圖 surface development
表面張力 surface tension
表面處理 surface finishing; surface treatment
表面硬化 case hardening
表面硬化鋼 case-hardened steel
表達方式 presentation
表達技巧；傳意技巧 communication technique
表觀膨脹；視膨脹 apparent expansion
金工 metalwork
金工工作間 metalwork area
金工角尺 engineering square
金工車床 metalwork lathe
金工虎鉗 engineer's vice
金工鋸床 power hacksaw
金屬包頭；金屬箍 ferrule
金屬配件 metal fittings
金屬線 wire
金屬壓展機 hand rolling mill
金屬擦光劑；磨光劑 metal polish
金屬薄片 sheet metal
金屬鍵 metallic bond
長方通 rectangular tube
長刨 trying plane
長螺旋鑽咀 long auger bit
長鏜孔 long boring
閘極 gate
阻抗 impedance
附件 attachment
附錄 appendices
青銅 bronze
非反相放大器 non-inverting amplifier
非本徵半導體 extrinsic semicon
慢慢找吧,下面個網站是汽車專業詞彙,可以去找找
Ⅵ 物流海運專用術語<英語》
看看如下的內容吧:
A
alongside -- The side of a vessel.
B
barrel -- A measurement term that refers to 42 gallons of liquid at 60 degrees Fahrenheit (15.56 degrees Celsius).
berth -- The structure where a vessel is secured for the loading and unloading cargo.
bonded warehouse -- A warehouse authorized by customs authorities for the storage of goods on which payment of ties is deferred until the goods are removed.
bow -- The front of a vessel. Also see "stern."
breakbulk cargo -- Loose, non-containerized procts. Examples include steel slabs and coils.
bulk cargo -- Loose cargo shipped in the cargo hold of a vessel without mark and count. Examples include coal, grain and sulfur.
bunker -- A maritime term that refers to fuel used aboard a vessel.
C
cargo -- Freight loaded into a vessel.
cargo manifest -- A list of all cargo carried on a specific vessel voyage.
cargo tonnage -- Most ocean freight is billed on the basis of weight or measurement tons (W/M). Weight tons can be expressed in short tons of 2,000 pounds, long tons of 2,240 pounds or metric tons of 1,000 kilos (2204.62 pounds). Measurement tons are usually expressed in cargo measurements of cubic feet (one cubic foot equals 0.03 cubic meters) or cubic meters (one cubic meter equals 35.31 cubic feet). Typically, 40 cubic feet (1.13 cubic meters) is the measurement standard.
carrier -- Any person or entity who, in a contract of carriage, undertakes to perform or procure the performance of carriage by rail, road, sea, air, inland waterway or by a combination of such transportation modes.
chassis -- A frame with wheels and container-locking devices in order to secure the container for movement.
container -- A truck trailer body that can be detached from the chassis for loading into a vessel, a railcar, or stacked in a container depot. Containers may be ventilated, insulated, refrigerated, flat rack, vehicle rack, open top, bulk liquid or equipped with interior devices. A container may be 20 feet (6.1 meters), 40 feet (12.19 meters), 45 feet (13.72 meters), 48 feet (14.63 meters) or 53 feet (16.15 meters) in length, eight feet (2.44 meters) or eight feet, six inches (2.59 meters) in width, and eight feet, six inches (2.59 meters) or nine feet, six inches (2.9 meters) in height.
container freight station (CFS) -- A shipping dock where cargo is loaded ("stuffed") into or unloaded ("stripped") from containers. Container reloading from/to rail or motor carrier equipment is a typical activity.
container terminal -- An area designated for the stowage of cargo in containers. Usually accessible by truck, railroad and marine transportation, the terminal is where containers are picked up, dropped off, maintained and stored.
containerization -- Stowage of general or special cargo in a container for transport in various modes.
containerload -- A cargo load sufficient in size to fill a container either by cubic measurement or by weight.
container port -- A seaport that features cargo terminals developed specifically to handle marine cargo containers.
D
dock -- For ships, a cargo-handling area where a vessel normally ties up. For land transportation, a loading or unloading platform at an instrial location or carrier terminal.
doublestack train -- A train using specialized railcars that enable marine cargo containers to be stacked one atop another.
draft -- The number of feet (or meters) that the hull of a ship is beneath the surface of the water.
dry bulk container -- A container constructed to carry grain, powder and other free-flowing solids in bulk. Used in conjunction with a tilt chassis or platform.
dry cargo -- Cargo that is solid in nature and normally does not require temperature control.
E
export -- Shipment of goods to a foreign country.
F
feeder service -- Cargo to/from regional ports are transferred to/from a central hub port for a long-haul ocean voyage.
feeder vessel -- A short-sea vessel that transfers cargo between a central hub port and smaller spoke ports.
FEUs -- Maritime abbreviation for "40-foot equivalent units," which refers to containers that are 40 feet (12.19 meters) in length. One FEU is equal to two TEUs, or "20-foot equivalent units." See "TEUs."
flat car -- A railcar without a roof and walls.
flat rack/flat bed container -- A container with no sides and frame members at the front and rear for cargo loading from the sides and top.
foreign-trade zone -- A free port in a country divorced from Customs authority but under government control. Merchandise, except that which is prohibited, may be stored in the zone without being subject to import ty regulations.
free port -- A restricted area at a seaport used for the handling of ty-exempt import goods.
freight -- Refers to either the cargo carried or the charges assessed for carriage of cargo.
freight forwarder -- A person whose business is to act as an agent on behalf of the shipper. A freight forwarder frequently makes the booking reservation.
G
gateway -- A point at which freight moving from one territory to another is interchanged between transportation lines.
gross weight -- The entire weight of goods, packaging, container and freight car, ready for shipment. Generally, the combined weight limit of the cargo, container and tractor for highway transport is 80,000 pounds (36,287.39 kilograms).
H
hatch -- The opening in the deck of a vessel, providing access to the cargo hold.
I
import -- Shipment of goods from a foreign country.
inland carrier -- A transportation line that hauls export or import traffic between ports and inland points.
intermodal -- A shipping term denoting the interchangeable movement of cargo containers between different modes of transportation, primarily ship, truck and train, where the equipment is compatible with the multiple transport systems.
J
Jacob's ladder -- A rope ladder suspended from the side of a vessel that is used for boarding.
just in time (JIT) -- In this method of inventory control, warehousing is minimal or non-existent: The container is a "movable" warehouse and must arrive neither too early nor too late
K
knot -- One knot is equal to one nautical mile (6,076 feet or 1,851.96 meters) per hour. In the early sailing days, speed was measured by tossing overboard a log secured by a line. Knots were tied into the line at intervals of approximately six feet (1.83 meters). The number of knots measured was then compared to the time required to travel the distance of 1,000 knots in the line.
L
laden -- Loaded aboard a vessel.
landbridge -- The movement of cargo, by water, from one country through the port of another country, by rail or truck, to an inland point in that country or to a third country. For example, cargo from Japan is landbridged across the United States to France.
liquid bulk -- Cargo that is fluid in nature and typically transported in tankers. Examples include oil and other petroleum procts.
longshoreman -- An indivial employed in a port to load and unload cargo vessels.
loose -- Without packing.
M
maritime -- Business pertaining to commerce or navigation transacted upon the sea or in seaports.
meter -- One meter is equal in length to 3.28 feet or 39.37 inches.
metric ton -- One metric ton is equal in weight to 2,204.62 pounds or 1,000 kilograms.
mile -- One mile is equal to 5,280 feet or 1.61 kilometers on land. Also see "nautical mile."
mini-landbridge -- An intermodal system for transporting containers by ocean and then by rail or motor to a port previously served as an all-water move. For example, cargo from China is mini-landbridged through Seattle to New York.
multimodal -- Synonymous with "intermodal" for all practical purposes.
N
nautical mile -- One nautical mile is equal in length to 607,612 feet or 1.85 kilometers, which is the distance of one minute of longitude measured at the equator. Also see "mile."
near-dock railyard -- A cargo facility used primarily to sort marine cargo containers and assemble into trainloads bound for common destinations. These railyards are located inland, in close proximity to a port waterfront.
non-vessel operating common carrier (NVOCC) -- A cargo consolidator in ocean trades that will buy space from a carrier and subsell it to smaller shippers. The NVOCC concts itself as an ocean carrier, except that it will not provide the actual ocean or intermodal service.
O
on-dock railyard -- A cargo facility used primarily to sort marine cargo containers and assemble them into trainloads bound for common destinations. These railyards are located on a port waterfront.
origin -- The location where a freight shipment begins its movement.
overheight cargo -- Freight that is more than eight feet high, or too tall to fit into a standard container.
P
pallet -- A platform with or without sides, on which a number of packages or pieces may be loaded to facilitate handling by a forklift or similar functioning equipment.
pier -- The structure where a vessel is secured for the loading and unloading cargo.
piggyback -- A transportation arrangement whereby truck trailers and their loads are carried and moved by train to a destination.
port -- There are three common definitions:
1. A harbor with piers or docks.
2. The left side of a ship when facing the bow. Also see "starboard."
3. An opening in a vessel's side, used for handling freight.
port of call -- A port where a vessel discharges or receives freight.
port of entry -- A port where cargo enters a country and is unloaded.
port of exit -- A port where cargo is loaded and leaves a country.
Q
quay -- A structure attached to land to which a vessel is moored. Also see 「berth," "dock" and "pier."
R
ramp -- A railroad terminal where containers are received or delivered and trains are loaded or discharged.
reefer -- An instry term for a refrigerated or temperature-controlled container.
relay -- The transfer of containers from one ship to another when both vessels are controlled by the same network (carrier) manager.
revenue ton -- A ton measurement on which shipments are freighted. If cargo is rated as weight or measure (W/M), whichever proces the higher revenue will be considered the revenue ton. Weights are based on metric tons and measures are based on cubic meters. Hence, one revenue ton is equal to one metric ton (2204.62 pounds) or one cubic meter (35.31 cubic feet).
roll-on roll-off (Ro/Ro) -- A method of ocean cargo service using a vessel with ramps, which allow wheeled containers, trailers or vehicles to be loaded and unloaded without the use of cranes.
S
service -- A string of vessels that makes a particular voyage and serves a particular market.
ship chandler -- An indivial or company selling equipment and supplies to ships.
shipper -- The person or company who usually is the supplier or owner of commodities shipped. Also called the consignor.
ships --There are nine basic types of ships:
1. barge carriers -- Ships designed to transport barges.
2. bulk carriers -- All vessels designed to carry bulk cargo, such as grain, fertilizers, ore and oil.
3. combination passenger and cargo ships -- Cargo vessels with the capacity for 13 or more passengers.
4. freighters -- Comprises refrigerated and unrefrigerated breakbulk vessels, containerships, partial containerships, roll-on roll-off vessels and barge carriers.
5. full containerships -- Vessels equipped with permanent container cells for container storage, with little or no space for other types of cargo.
6. general cargo carriers -- This category includes breakbulk freighters, car carriers, cattle carriers, pallet carriers and timber carriers.
7. partial containerships -- Multipurpose containerships with one or more, but not all, cargo compartments fitted with permanent container cells. The remaining compartments are used for noncontainerized cargo.
8. roll-on roll-off vessels -- Specialized ships designed to carry wheeled containers, trailers and vehicles using onboard ramps.
9. tankers -- Ships fitted with tanks for storage of liquid cargo, such as crude petroleum and petroleum procts, chemicals, liquefied gas, wine and molasses.
short ton -- One short ton is equal in weight to 2,000 pounds or 0.91 metric tons.
side loader -- A lift truck fitted with lifting attachments operating on one side for handling containers.
slip -- A ship's berth between two piers.
spreader -- Equipment designed to lift containers by their corner casters.
stack car -- An articulated five-platform railcar that allows containers to be doublestacked one atop another.
stack train -- A rail service whereby railcars carry containers doublestacked on specially operated unit trains.
starboard -- The right side of a ship when facing the bow. Also see "port."
stern -- The end of a vessel. Also see "bow."
stevedore -- A person or company that employs longshore workers and establishes agreements to load or unload ships.
stowage -- A marine term that refers to loading freight into vessels' cargo holds.
straddle carrier -- Mobile truck equipment that is capable of lifting containers within its own framework.
supply chain -- A logistical management system that integrates the sequence of activities from delivery of raw materials to the manufacturer to delivery of the finished proct to the customer. "Just in time" is an example of supply chain management.
T
tariff -- A publication that sets forth the charges, rates and rules of ports and transportation companies.
terminal -- An assigned area where containers are prepared for loading into a vessel, train or truck, or are stored immediately after discharge from the vessel, train or truck.
TEUs -- Maritime abbreviation for "20-foot equivalent units," which refers to containers that are 20 feet (6.1 meters) in length. Two TEUs are equal to one FEU. Also see "FEU."
transship -- To transfer goods from one transportation line to another, or from one ship to another.
turnaround -- In water transportation, the time between the arrival and departure of a ship from a port.
U
unit load -- Packages loaded onto a pallet, in a crate or any other way that enables them to be handled at one time as a unit.
unit train -- A train comprising a specified number of railcars that remain together as a unit until reaching a designated destination.
unitization -- The consolidation of a quantity of indivial items into one large shipping unit to facilitate handling. Also: The loading of one or more large items of cargo onto a single piece of equipment, such as a pallet.
V
vanning -- A marine term for stowing cargo in a container
warehouse -- A place for the reception, delivery, consolidation, distribution and storage of cargo.
W
warehousing -- The storage of cargo.
weights and measures --
1. One cubic meter is equal to 35.31 cubic feet.
2. One long ton, or gross ton, is equal to 2,240 pounds or 1,016.05 kilograms.
3. One measurement ton is equal to 40 cubic feet or one cubic meter.
4. One metric ton, or kilo ton, is equal to 2,204.62 pounds or 1,000 kilograms.
5. One short ton, or net ton, is equal to 2,000 pounds or 907.18 kilograms
Y
yard -- This term commonly refers to a railroad yard with many rail tracks for assembling, storing or switching freight trains.
Ⅶ 幾種螺絲刀的英文單詞
你好，電動螺絲刀的空載轉速
翻譯成英語是：idle
speed
of
electric
screwdriver
——————如有幫助請採納，謝謝。
Ⅷ 英語Empty set怎麼翻譯
empty set：數學裡面集合術語 空集；空集合。
專業術語解釋：空集(empty set):約定存在一個沒有任何元素的集合,稱為空集,記為φ,有時也用{} 來表示.按子集的定義,空集是任何集合的子集。
相關短語：
axiom of empty set空集公理
axiom of the empty set空集公理
non-empty set非空集 ; 非空集合
雙語示例：
Startfromscratch: Start .
從頭開始：從一組空的條件開始並添加您自己的條件。
This ,so by nothing (oremptysetbyemptyset).
之所以會出現這個問題是由於欄位是空的，因此實際上進行的計算是零乘零（或者空集乘空集）。